How to Replace a Kia Sportage Replacement Key

The key of many Kia models has an electronic keyless entry system built into. The key functions like the remote control, and is exchangeable by a Kia dealer.

Key fobs may stop working due to a number of reasons, such as a dead battery, worn-out buttons, signal interference or water damage. Here are some tips on how you can get your kia replacement key fob Sportage replacement key working again.

How do you replace the remote key or smartkey?

The battery inside your Kia's smart key will eventually require to be replaced, regardless of whether it is a remote key, a push-to-start key or a standard metal key that does not contain an electronic transponder. This is especially true if your car displays a message that indicates the remote or smart keys aren't powered.

It's a simple process. In order to replace the battery in the key fob remove the mechanical key from the slit in the back of the key fob. Then lift the cover. Inside the key fob will be the small screw that holds the battery in its place. Utilizing a small screwdriver take the screw off and remove the old battery. Install the new battery and close the opening on the key fob.

When the key fob is equipped with a fresh battery and you've tested it, press the locks and unlock buttons. If the doors lock and unlock as expected, then you're good to go! You can now use the hands-free feature to lock and unlock your Kia whenever your fingers start to get chilly or when you need to do some errands in Brandon.

Note: Certain key fobs (transponder chip or smart keys) might require their programming completed. This requires a computer that is only available to the automotive locksmith or dealer. Other keys (non transponder metal keys), do not need programming. If you're looking to reprogramme your key, you'll need to note the key code number on the tag for the key code.

How do you replace a dead battery?

If the Kia key fob is unable to respond when you press the lock/unlock button, it is most likely that the battery is low. A battery that is not functioning properly can cause other issues, such as the check engine light turning on or the engine not cranking properly. Fortunately, replacing the battery on the key fob is a fairly simple DIY project that requires just some basic tools.

Make sure that you shut off your vehicle and shut all doors prior to beginning. Find the small, metal or plastic piece on the bottom of the key fob. Move it until the key is released. Then, you can insert the key into the driver's door handle to open your car.

To replace the battery in the key fob remove the cover at the rear. Use a pry tool to remove the latch that holds the black negative cable. Remove the old battery, and then align the new battery to ensure that the "+" positive side faces you, and the "negative" negative side is facing towards the fob's metal electrical contacts. Avoid using excessive force when pushing the new CR2032 into position to avoid damaging or bending the metal contacts.

Once the new battery has been installed then turn the key fob off and on in the ignition for a few times until the door locks cycle. You can then test your Kia key fob to determine whether it's working again.

How to replace a smart keys

You may have either a standard keyfob, or a Smart Key, based on the model of Kia Sportage. The smart key is equipped with an embedded mechanical key blade, however, the standard key fob does not. Both types of key fobs are equipped with a battery inside them that will eventually have to be replaced. It is a simple process that takes just two minutes.

Be sure to turn off your Kia, and be on a flat and well-lit surface prior to you begin. Be aware that the fob can contain tiny pieces that could fall should you not be careful.

The first step is to find the small release button that is located on the backside of the fob. It's either a circular button or a rectangular slot. When you press it button, the mechanical blade will appear and you can then open the key fob.

Once you have the key fob opened and you are able to remove the old battery and replace it. The new battery is a CR-2032, and can be purchased on the internet or at your local auto parts shop. After you're done, your key fob should permit you to lock or unlock and start your vehicle even if it's not running.

How do you replace a broken mechanical key

The Kia key fob is an amazing convenience that allows us to lock and unlock our car with the push of a button. But like any device it will encounter issues occasionally. There are steps that can be taken to resolve these issues and ensure that our key fobs are in good working order for the long run.

One of the most frequent problems is a weak or dead battery. This could cause your device to stop working or work intermittently. If this is the issue, replace the battery with an entirely new battery.

If this isn't enough to solve the issue, you can use the flathead screwdriver that is standard to push the fob's plastic casing open. Be careful not to damage any internal components or scratch the plastic. Once the battery is removed and replaced, you can replace it with a brand new battery.

Close and open the door using the mechanical key. (Every Kia fob comes with a spare mechanical key that fits into the slot). Test the key fob to check that it's functioning correctly. Contact a dealer, or a locksmith to address the issue when the fob still is not working. Make sure they make you an emergency key that can work in all the trunk and door cylinders, to avoid lockouts in the future.