How to Replace a saab 9-3 key (check out this site)

The Saab 9-3 is a great car that has a lot of driver appeal. It has a powerful engine as well as excellent visibility. It has a very high safety rating.

It is essential to have two keys that work for your vehicle. If you lose one key, it could be expensive to replace it with another one.

How to replace the ignition Key in a Saab9-3

You'll must replace the car key when it doesn't turn. This guide will walk you through how to do it on the saab key code 9-3. You'll need a new key as well as a reprogrammable battery as well as a new key-fob case.

Unlike older models, most modern Saab vehicles use transponders in the key-fob instead of a physical key to unlock and start the car. The reprogrammable batteries in the replacement key for saab 93-fob inevitably become worn out and cannot hold any charge. This is especially true if you use the same key for the lock you have.

A professional locksmith can change the battery with ease. You can also do it yourself if have the appropriate tools and a bit of patience. The first step is to separate the key-fob. This is done by inserting a flathead screwdriver in the slot that is located in the middle of the case. The plastic is thin and can easily be damaged.

After the case has been opened and you are able to prepare the new key by combining the lower half of the key that was used previously with the banana and transponder on the new key. This will ensure that the new key is properly mated to your CIM that can be a major difference when replacing the sole key on your Saab 9-3.

How do you replace the ignition Key in a Saab 900

Unless you have two keys, you will have to take off the steering wheel and dashboard to gain access to the ignition. Begin by disconnecting the negative battery cable. Once the battery is disconnected, you are able to remove the trim and dashboard pieces around the steering wheel. Once the dash is removed, you can push a screwdriver into the opening on the back of the ignition switch and take it out.

The ignition cylinder has key locks that can stop the car from starting if a key isn't inside it. If the ignition switch on your 900 isn't functioning correctly, make sure to check if the key is in the lock or is stuck inside the barrel. You should also rotate your keys and keep them clean to avoid bending.

Saab cars differ from other cars because they don't use traditional keys made of metal. Instead, the car recognizes the key fob's electric signals through a chip that is specifically designed for it.

If you lose only one key fob that is working, your dealer will charge the cost of replacing your computer module (also called the CIM). We can reprogram the EEPROM on your computer to enable it to accept new keys, without having to replace it. This can save you more than 50% of the price the dealer charges! We call it the SAAB Key PROGRAM. Find out more here!

How to Replace the Ignition Key in a Saab9-5

The metal part of a classic Saab key is simple to copy, and it's also not much of an impediment against theft of a vehicle. The electronic component of the key-fob comes with a chip that recognizes the car when the key is put in the ignition switch.

Saab has relied on the technology of this anti-theft system for more than a decade. It's not as effective as a physical lock for your door but it does make stealing your car more difficult. This is the reason why every saab key programmer owner should always have an extra key available.

The majority of new Saabs come with two keys in the factory. However, you can upgrade them at an agent using a handheld computer referred to as a Tech-2. The cost can be under $400 for the transmitter+transponder (different than the metal replacement key for saab 93 blade/shell that opens the doors and turns the ignition cylinder). The only exception to this rule is NG 9-3 vehicles, which have more modern, more advanced features that require an ignition key.

The dealer will replace the CIM or TWICE module in these cars if all keys are lost, and charge you top dollar for the process. We can reprogram your computer's EEPROM to accept new keys without replacing expensive modules.

How to replace the ignition Key on the Saab XC90

If your SAAB 9-3 key fob begins having issues turning the barrel of the lock it's possible that it's time to replace it. It's quite simple and doesn't require you to visit an agent. Instead you can do it yourself at home with a few simple tools.

First, you'll need to prepare the new keys. Before you begin, disable the anti-theft by placing blocks under your rear wheels and releasing your handbrake. Put the key into the ignition and turn it to the "on" position. This will activate the accessories, however, it won't start the engine. Repeat this five times, then leave the key in the on position.

You'll need to purchase an additional case for your key fob. You can find these at any auto parts shop, and they're typically quite affordable. Depending on the model, you can even buy them without electronics.

To open up the case, place an flathead screwdriver into the slot that is in the middle, and gently work it. After you have split the case, you will be able to access all the internal electronic components. Use a flathead screwdriver to gently pry out the electronics.