How to Replace the Replacement Key Battery For the Saab 9-3

Saab owners have to follow a series of special steps to install an additional ignition key. This requires an electronic handheld computer, referred to as Tech-2, to be used by the dealer. Then a new key as well as transponder are required to be purchased and then programmed to the car.

It is a good idea to rotate your keys in order that one doesn't wear out more quickly than the other. This will help keep your keys in top condition.

Replacement Case

Unlike the classic Saab keys of old keys, the latest key fobs are equipped with electronics which makes it difficult to make a copy. This has made stealing car keys much more difficult than it was twenty years ago. It also makes it more expensive to replace lost keys.

Every owner of a Saab 9-3 needs to have at least two functioning keys. If one is lost, it costs a fortune to add another to the car since it requires replacing the CIM module, and then reprogramming the locking cylinders. Dealers charge between $100-$200 to do this.

There are ways to avoid the high cost. Certain parts suppliers will utilize the code of the spare key to cut a new metal blade for less than what the dealer charges. The key must be exactly the same as the original for it to work in your vehicle.

Follow these steps to replace the case. You will need a flathead screwdriver along with some patience. Utilizing the screwdriver, slowly pry the plastic apart and separate the emergency key from the case. Once you have the case open, remove the electronics and put them back into the new case. Be sure to put the correct key and badge back inside the case, too.

Replacement Battery

The Saab 9-3 replacement battery is a cheap component that can be easily and quickly replaced. Cyclone's YouTube video Cyd shows how to get a saab key replacement replacement key [linked web page] to replace the battery for the remote fob in just four easy steps. This guide should work with any modern saab-type key fob, however, the procedure may differ slightly.

This button is usually placed just below the Saab logo on the back of the fob. This button is typically located on the back of your fob close to the Saab Logo. Then use a flathead screwdriver to insert into the small hole of this button. This should be enough to open the fob's case so that you can replace the battery.

After the new battery CR1632 is installed then you can reassemble your remote key fob, and then program it to your car. The whole process should take more than an hour, how to get a Saab replacement key if not less. It's a simple process that does not require any special tools.

The procedure is a little more complicated in the event that you lose the key, but it's possible. The dealer will first need to read the VIN of the vehicle before requesting the replacement TWICE module as well as key blade that has the correct unique code. The dealer will then have to program the key using MDI, a new software tool.

Replacement Key Fob

The key fob is the part that locks and unlocks your car. It has an internal battery. Batteries are able to last for a short time and eventually will die. It's a common issue for all vehicles. The good news is that you can change the batteries in most key fobs, without having to replace the entire case. You can buy replacement saab car keys fobs on Amazon that have all the electronics already installed, which means you can simply open the case and replace the batteries that were in the case. It is important to keep in mind that you'll need to remove the emergency key first. you can do this by inserting a small flathead screwdriver into the slot in the middle of the case. Move the screwdriver around the case, and it should split open, making it simple to take it out.

If you are about to replace the keys, ensure you have spare keys, since this will cut down the total cost by a significant amount. If you have a spare, you can request that the dealer cut an entirely new key and then program it into your car, which is cheaper than replacing the entire key fob.

If you don't have a spare you can add an additional key to your car, but this will require a lot of research and effort. It costs a few hundred dollars to add an additional car key. The computer in the vehicle must also be programmed. Professionals can do this but it's not a cheap option.

Replacement Ignition

The current SAAB 9-3 uses an alarm system that is more sophisticated based on a key code. This means that if you lose your only working key, adding another one could be very costly since the car needs to have a special computer module installed, and it must also be specifically designed to accept a different key. Even a dealer can charge hundreds of dollars to program an entirely new key, if they are unable to do it.

Dealers will charge you a premium to replace your car computer (also called the CIM or SAAB twice) if you lose your only working key. We can reprogram the EEPROM in your car computer to be ready for an additional key. This will save you more than 50% off what you would have to pay an auto dealer.

If you have owned a 9-3 from SAAB for quite a while and you're aware of the ignition keys aren't very durable. If your ignition key isn't working correctly, you should look into replacing it. They can become extremely sticky and the buttons have been known to fall off. It's not as difficult as it appears to replace the ignition key. With the appropriate tools, it could be accomplished quickly.