peugeot 508 key 208 Key replacement car key peugeot 207

It is better to leave the replacement of Peugeot keys for 208 to auto locksmiths that have the required equipment and skills. They can program and create keys faster and less expensive than a dealership.

If your key fob stopped locking or unlocking your doors it is likely due to a dead coin battery. There are also other reasons why the key may be malfunctioning.

Dead Coin Battery

A dead coin battery will stop your Peugeot 208 from locking or unlocking, and won't start the engine. In this case, you will need to choose the alternate method to start that is described in the owner's manual.

The spark plugs can also be worn out. The spark plugs ignite the fuel to start the engine. However they are limited in their time of life. They'll eventually degrade in the event that they aren't utilized enough.

There is a straightforward solution to this issue. Examine the voltage of your battery using a multimeter. If the voltage falls below 11,5 volts, then it's time to replace it. If the battery has corrosion, it is important to clean its contacts. You can do this by lifting the rubber covers that protect the two terminals of the battery and using a wire brush to remove any corroded components of the battery. Then, you should reconnect the positive and negative pole cables.

Water Damage

If your 208 doesn't start and the battery has not fallen flat, it is time to examine the spark plugs. You may find that they are simply too dirty and do not spark. This can be fixed easily by cleaning the spark plugs in a workshop.

Peugeot automobiles use keys that are transponder-type and works with the car's immobiliser system. This makes sure that only the correct key is able to turn the engine. If the chip inside the Peugeot key is damaged, then it won't send the correct signal to the vehicle.

This is a common problem that can be caused by water damage. This is most common in colder climates where the vehicle might have been exposed to rain or snow. In this instance, you should contact a reputable locksmith who has the required tools and equipment to modify the key. They also have the most up-to-date technological know-how and machinery required to create a Peugeot 208 smart key. The process shouldn't be more than 15 minutes.

Contacts to the battery are not working properly.

Peugeot replaced the old transponder chips with a new model that is based on electronic components mounted on a circuitboard. The new system is great when it's new, but the circuit boards wear out over time and stop working properly.

This can stop the immobiliser from working, so the vehicle won't start. If this is the case it's a good idea to call a Peugeot specialist or locksmith.

Another common issue is when the battery for the key fob is dying, this causes the blade of the key to stop being able to feed into the lock. A locksmith from your car will replace the battery, and then cut a fresh blade for you. This is a quick fix.

Faulty Receiver Module

It could be that the receiver module has a problem If your Peugeot key fob fails to function after being dropped on the floor, or exposed to a sudden storm or accidentally washed. The receiver is responsible for sending radio frequency signals to an on-board computer, which is responsible for controlling the centralized locking system inside your peugeot 107 key replacement vehicle.

The key fob itself is fitted with rubber seals that prevent water from reaching the chip inside. However, prolonged exposure to water may cause damage to these seals and the chip. The high salt content of the pool or ocean water can cause damage to the key fob, especially if it is submerged.

If your Peugeot spare key fob isn't working You'll need the module replaced. This should be done by an Peugeot specialist or an expert auto locksmith. Peugeot keys unlike other automobiles, are protected by an immobilizer system. This requires the right programming to allow the car to start. This is why you should be able to trust a professional peugeot key cutting locksmith with the task of designing and programming an appropriate replacement.

Faulty on-Board computer

The computer on the board of your peugeot 206 key fob replacement is responsible for a variety of the systems inside your vehicle, from power windows to airbags. The on-board computer will display a code if something goes wrong. This code is stored inside the system and will remain there until the problem has been resolved. This will often require the on-board computers to be replaced.

One of the most common reasons for the light turning on is loose or corroded connectors in the airbag sensor. It can be due to wear and tear, ageing or exposure to salt and moisture. This issue needs to be addressed as soon you can, since an airbag that's malfunctioning could be dangerous in the event of an accident.

If your Peugeot is showing a card detected as not present error then the key battery in the key fob might be dead or weak. This will stop the key fob from sending a signal to disarm the immobilizer in your vehicle. Test this by pressing the unlock button on the key fob, and then trying to start your car. If this does not work it is likely that the battery needs to be replaced.