how to repair broken car key to Repair car key Repair company Keys

Car keys may appear tiny and insignificant, but they are vital for the proper operation of your vehicle. Replacing an old key or a transponder one can cost upwards of $200.

However, there are ways to fix your car keys at home with only a fraction of the cost. This article will cover the most frequently encountered emergency car key repair keys issues and their DIY solutions.

Dead Key Fob Battery

The remote key fob repair key fobs for keys that come with cars make it easier than ever to open the trunk, doors and the tailgate. The battery in this device is susceptible to dying. However, there are a few tricks that can be used to solve this problem in the event of a need.

First, determine if the car is in ignition mode. If it is, the battery on the key fob could simply be depleted instead of dead. To test, press the button on the fob against the ignition button of the vehicle. If this works, then the battery is probably working fine and only has to be replaced.

To replace the battery in the fob, open the case with the screwdriver. Do not apply too much force, as this may cause the fob's casing to split. If the fob isn't opening, try using your pry tool more than once around the outside of the case.

Open the electronic compartment of your vehicle after you have removed the mechanical key. Insert the new battery and then snap back the shell. If the key fob won't work after this, there may be a bigger problem with your car key repair cost's remote start system that requires a professional diagnostic. If this is the case, a trusted mechanic should be able to help you. If you require assistance with your vehicle and you need help, you can call roadside assistance.

Broken Key Ring

If your key fob isn't functioning because the ring has broken there are a few options you might try. Look to see if can locate the broken part in the ignition. If it is, remove it without damaging the lock on the ignition or door lock. If you are having trouble getting it out, contact a locksmith for help. They have special tools that allow you to safely remove a damaged key from the ignition.

Another reason that can lead to broken car keys is the corrosion of the circuit board or frame. You can clean the board with the help of rubbing alcohol and a cotton swab. This will eliminate the corrosion and prevent damage to the contact pads.

If your key isn't starting because the ring is broken, you may be able to repair it with a strong wire or nail to close the hole. Superglue can be used to fix the broken key ring. After cleaning the ring with a wet cloth, apply a small amount superglue on each end of the nail or wire. Let the pieces dry and then press them into place. These DIY solutions might look appealing, but they're just temporary solutions. It's best to hire an expert locksmith for repairs that last. They have the experience and tools to repair a broken key quickly and efficiently. They can even replace the battery in the key fob and change it's programming if required.

Broken Key Blade

Some key blades may break due to wear and tear. If this occurs, you must buy a new one. Fortunately, this issue isn't as severe as it appears at first glance. The problem is that the blade has snapped away from the case.

One solution is to spray the key hole with a lubricant. You can then make use of pliers or tweezers grasp the broken end of the key and pull it. You may also make use of a magnet if the key is magnetic. Use a magnet to assist you remove the key, but be cautious to not break the lock tumbler.

If you're not able to get the broken piece of key, call an expert locksmith immediately. They have the right tools that can safely remove keys without causing damage.

You can also try super glue to repair a snapped key. Apply a small amount to the edges and press them together. Make sure the glue has dried before inserting the key into the lock. But this method isn't very secure and you may need repeat the process several times before it is successful. In addition the super glue may not be enough to keep the key in place. This is more of a temporary measure rather than an option that can last.

Broken Plastic Loop

If the plastic loop breaks off, it can make the key useless. Luckily, this is an simple fix. To replace it alternative, you can opt for an extremely thick wire or a finishing nail. For each end of the nail or wire make two holes in the loop of plastic. Cut the nail or wire to the desired width and then put a drop of superglue in each hole. Put the nail or wire into the holes until it closes them, and then let it dry.

Another option is to purchase the replacement shell from a locksmith who sells them. They can take the programmable portion of your key, transfer it to the new shell and cut an entirely new blade for less than a full replacement cost.

This is not the best option, but it can help you get back on the road once more if your key broken in half. It's difficult to repair if the key blade is in the ignition, however. You could try using hair clips or a needle extractor tool to remove the damaged part out of the ignition, however this can be risky if not careful. Get a locksmith equipped with special tools to safely remove damaged keys from ignitions. You can also get a new key that is made using the proper cuts for the ignition of your vehicle.

Broken Master Key

If a key is broken inside the lock, you'll have to attempt to retrieve it before it's completely destroyed. There are a few techniques you can employ, such as using lubricants as well as tools such as needle nose pliers and tweezers to take a small piece of the damaged key and pull it out.

To begin, spray the inside of your lock with a lubricant, such as graphite powder or WD-40. You may also try the hacksaw blade method that involves carefully sliding the blade along the side of the broken key and attaching it to the teeth - if you are able to do this, you will be able to pull out the broken key from the lock.

Many hardware stores carry tools for key extraction that spiral. It is a thin, flexible bar with spiral threads, that can be inserted into the keyway and then bent to get into the broken part of the key. Once it is hooked to the serrations, you can turn it in a circular direction and push it against the damaged section of the key to get it out.

It's worth trying to get rid of a broken master key before calling an expert locksmith. If you're not able to take the broken piece off it's time to contact a professional locksmith. A locksmith can make you a new key that will be programmed using the transponder of your car.