Repairs to uPVC Windows

uPVC is a great choice for modern homes. They are easy to maintain and durable, as well as long-lasting. As opposed to aluminium and timber they do not get rusty or decay.

Regularly cleaning and lubricating UPVC windows and doors is crucial. This will reduce unnecessary repair costs and increase energy efficiency.

1. Broken Glass

The broken glass in your windows could cause serious damage to your home and may even be fatal. It is important to take the time to make sure that you are doing everything you can to keep your windows in good shape.

Single-pane windows are relatively simple to replace and generally fit into frames of the past easily. If you have double-paned windows which are joined by internal beading, it is difficult to remove and replace the old panes. In this instance it is essential to purchase plastic spacers to make sure that the new pane fits into the window frame.

Wearing protective eyewear and thick gloves is a must when you are planning to remove the glass by yourself. It is also an excellent idea to lay down a dropcloth before you start working on the glass to ensure that any shards fall on the fabric instead of onto the floor where they can be trampled upon and cause further damage.

It's a great idea to cover the gap with tape after the glass has been removed. This will keep drafts and water from entering your property until a professional arrives to repair the window. This will also provide an obstacle to stop criminals from getting into your home. If the gap between the window and the door is substantial, you may prefer a security screen that also includes a window. This will provide the best of both.

2. Sagging

uPVC is a durable, energy-efficient and affordable alternative to timber sash window. In time, they could be affected by a variety of issues that include sagging. A sagging uPVC window can cause issues with light, draughts and even security. If you notice that your uPVC window is beginning to shrink, it's important to act quickly to prevent the problem from becoming worse.

To repair a window that is sagging, you can try to reposition the hinges. To do this, window repairs you'll have to open the window to get to the frame. Then, using an screwdriver, remove the hinges at the top and bottom and window repairs adjust them by turning them clockwise or anti-clockwise. Once you've repositioned the hinges, close your window and verify the fitting. If you are happy with the fit of your window, tighten the screws to hold them in place.

If you can't reposition the hinges, you may need to replace the seal. Rubber seals can dry out and lose their elasticity over time, leading them to loosen. If this happens, it's important to replace the seal as fast as you can to ensure that your uPVC windows are waterproof and draught-proof.

uPVC handles can also become loose. Often, this is caused by screws that have become loose over time. However, it could occur because the handle mechanism has worn out. It's relatively easy to fix a loose uPVC hand. First, you'll need to close the window and then perform a test to ensure that it fits. The joint at the corners of the sash must align with the joint on the casing. If it isn't you can use a screwdriver to loosen up the handle. Then turn the mechanism to position.

3. Water Leaks

It is crucial to take action if you awake each day to find a smoky wall and floors that are wet. Windows that leak water do can not only cause destruction of your home's structure but also hinder your efforts to control the temperature in your home. The most common cause for leaks in uPVC windows is that the sealant surrounding the frame is damaged or not present.

It is a fairly easy fix that can be done by any DIY expert. Depending on how severe the issue is, old caulking may have to be removed. It is essential to remember that when it is about uPVC window repairs you should not be tempted to apply too much caulk' as this will only make the area harder to clean and could reduce your energy efficiency.

It is important to check that any drainage holes are clear of debris and that the sill pan has been angled correctly so that it drains away from the window. In more extreme situations, you may have to replace the window.

Moldy sills and rotten ones are other signs of water leakage. The is a fungus that thrives in damp conditions and can quickly spread throughout the home.

It is also important to remember that if the leakage is coming from between the glass of your double glazing repairs glazed windows, it is more likely to be a problem with the glass seal rather than the frame or sliding. Again this can easily be fixed by a uPVC window specialist who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or loose and open with ease, it may be hinges that are at the fault. These are easily replaced by any competent DIYer and can usually be done within a few minutes.

Like any mechanical part hinges will wear out over time. It is very easy to change the hinges on a window but it's much easier if someone else helps you hold the frame.

It is also important to verify that the uPVC hinges are opening and closed in the correct direction. Check for the arrows on each hinge to determine which way the window should be opened.

The problem can be caused either by opening the window incorrectly or by a poor installation at the factory. Sending us a picture via our website is often enough to resolve the problem. We are happy to offer assistance.

Regularly lubricating the hinges is essential. This can be accomplished by applying a light engineering oil to the hinges. We suggest using a solvent-free lubricant such as the 3-in-one Multi-Purpose oil. Regular lubrication can make the window easier to open and close. It also decreases the chance of windows getting stuck and stop corrosion. The ideal time to do this once a year. WD40 and other solvent-based fluids are not recommended since they will damage parts of your uPVC window.

5. Draughts

Draughts can be caused by several different factors. The hinges, also due to wear and tear could become misaligned. This will cause an opening to appear where the sash joins the frame. These can be easily repaired by giving them good clean, but when they're beyond repair, it may be necessary to have them re-aligned or replaced. The interlock may also become unbalanced. This happens on the hinge's side, and might require to be cleaned. In certain instances it might be necessary to replace the hinges.

These seals are susceptible to wear and tear or be damaged over time, allowing air escape. Replacing these with high-quality weatherstripping can help keep draughts at bay. Another alternative is to replace the window with low-emissivity glass. this will help to regulate indoor temperatures and again will lessen the risk of draughts.

The last way to reduce draughts effectively is by using a Draught-exclusion device. These are usually made of fabric tubes filled with a filler that can be hung over your window sill. They will help stop cold air from entering and keep your home warm and cosy!

The windows made of upvc can continue to provide excellent insulation and security for your home with regular maintenance and repairs. It is important to remember that all windows will eventually wear out and it may be more cost-effective to replace them instead of fixing them. If you encounter any issues with your window made of upvc you should consult an expert immediately.