Cat flaps let your pet leave and come whenever they want without you needing to let him in or out. They also prevent your cat from peeing in the house.

Fitting a cat flap in the door panel made of upvc is much easier than in a glass door, but it does require some skills and the right tools.

Measure the Door

The installation of a cat flap inside the door isn't easy but as long as you use the correct type of cat flap make sure you take your time and follow the steps provided it should not prove to be too difficult. We will show you how to draw the shape, use a jigsaw to cut out the door's opening and then finish the job by fixing the cat flap to the door. This will ensure that the flap stays in place and shields the door from rain and wind damaging the door.

The first thing you need to do is take a measurement of the width of your pet in order to determine an accurate estimate of what size of cat flap you'll need. This will let you choose a cat flap that is big enough for your pet to go into the house and leave without having to open the back door with cat flap fitted each time.

If your kit has an illustration of the location to drill, then stick it on the door and then draw around it. If your door has moulding or a sill at the bottom, make sure that you leave enough space between your cat and these elements.

Next put on your eye protection and a dust mask. Then using a jigsaw start cutting according to the lines you penciled in, but don't press the blade too hard, as this could cause it to cut faster than you want it to. Set the square with a ruler to ensure that you're cutting the material in a proper manner and that the cut is a rectangle. Once you are satisfied with the result, you can take out the rest of the door material.

Draw a Line

The cat flap is a great method to allow your pet to go in and out without worrying about them coming in with a visitor, or leaving unwanted gifts inside the house. It also helps prevent draughts and helps keep your home's temperature in check. However, installing a cat flap in your door can seem like an overwhelming task for those who haven't done it before, which is why many people to call a professional carpenter or joiner to complete the task. It is an option, but you can do it yourself, provided the tools are appropriate and the steps are adhered to.

It is much easier to do with wooden doors, but it is still possible with uPVC. However it is important to be cautious not to harm the doors since this could make it impossible to claim your warranty. First, you must take measurements of the door to make sure it will accommodate the new cat-flap. If you have an ordinary uPVC panel it's easy. However, if your door is made of composite or another kind of door, you might require more care.

The next step is to determine the height of your belly for your cat. This is the measurement from the floor to the underside of the cat's stomach, and you will need to find a spot in the door where this measurement will fall within the range that your pet can comfortably go through wall cat flap. Once you have this information you'll need to mark out the area using pencil and a spirit level to ensure that the hole you will make will be suitable for your cat.

After you have marked the area, it's time to cut the hole. You will need to use a jigsaw and it is important that you take your time in order to ensure that the cuts are clean and smooth instead of uneven and rough, as it could cause damage to your door. Wear safety glasses and a dust mask when using the Jigsaw. Inhaling sawdust can be harmful for your health. Once you've finished cutting the hole, you'll require sandpaper to smooth the edges so that the cat flap is easily inserted.

Cut a Hole

It can be a challenge to fit an animal flap on a door panel or sealed double glazing unit. You may be tempted to tackle the job yourself, but unless have plenty of experience in DIY it is probably best to get a professional in to do the task for you. A mistake could not only look ugly and unattractive, but could also be security risks. It could let cold air in when the cat is outside and hot air out when inside.

Mark the hole's position on the door using an eraser and a spirit level. This will ensure it is positioned correctly and is flush with the rest of the door. Make sure to have sandpaper to smooth any rough edges.

Once the line has been marked you should cut out the hole with a jigsaw. Be sure to wear the appropriate safety equipment when working with a power tool. If you're worried about noise, you can purchase an electric jigsaw that is quieter and more user-friendly.

You should only remove the material needed to fit the cat flap cost flap. A little bit of extra material is required to increase the thickness of the wall of the cat flap itself but cutting off more than this could cause issues and damage the doors frame.

A upvc door may have a metal frame or panel which could block the microchip cat flap if this is the case, you'll need to make an over-sized hole to ensure that the metal doesn't come into contact with the wall of the cat flap. If this is done, it is essential to fill in the oversize gap and seal it with water.

If you are Fitting cat Flap in upvc Door panel a cat flap into the frame of a double glazed window with a metal frame, you will need to speak to a specialist who can supply you with a new glass pane that already has the hole for the cat flap already drilled in it. This is less expensive than trying to install a cat flap in an existing pane of glass that was not designed for this purpose.

Fit the Flap

Cat flaps allow your pet to come and go whenever they want, allowing them the freedom to lounge inside the house whenever they want to. If you have an uPVC front door, it can be difficult to put in the cat flap. This is especially true if you do not own a glass panel which can be cut. If you're willing to install a half-glazed uPVC replacement panel, it is possible to install a cat flap. It's not just a matter of slicing holes in the door. You'll also have to do a few things to ensure that the door is safe.

A composite door cat flap, upvc cat flap door panels, or GRP door panel is typically comprised of a thin plastic skin that is attached to an insulating polystyrene base. It is essential to be careful when cutting the material. This kind of door has a template can be used to cut the hole.

Once you've determined the location of the hole in your door, it's time to put in the cat flap itself. You can choose from a variety of models, ranging from simple push-button flaps to microchip activated ones that allow your pet in. However, no matter what kind of cat flap you pick, it's crucial to ensure that your cat can comfortably use the flap without getting stuck outside in the rain.

It is a good idea to choose circular fittings rather than a square one, as circles are more securely cut into door glass. This is because square holes can make the glass more susceptible to cracking when drilling is applied to it. It's also a safer option as you don't risk having to drill into toughened glass that may break and injure your pet or family members. This is especially important if you have child or elderly person at home who could be hurt by shards of glass.