How to Replace a Kia Sportage Replacement Key

The key of many kia picanto key replacement models comes with a keyless entry system built into. The key can be compared to the remote control and can be replaced with a new one from a Kia dealer or a locksmith.

Key fobs may stop working for several reasons, including batteries that are dead, worn buttons water damage, signal interference and a faulty receiver module. Here are some suggestions on how you can get your Kia Sportage replacement key to work again.

How to replace a remote key or smartkey

It doesn't matter if your Kia comes with an intelligent key, remote key, push-to-start key, or regular metal non-transponder key, the battery in these keys will eventually need replacement. This is especially in the event that your car displays a message that the smart key or remote has low battery power.

It's a simple process. To replace the keyfob battery remove your mechanical key from the slit that is located at the back of the fob. Then, push the cover open. Inside the key fob, there will be a small screw that holds the battery in the correct position. With a small screwdriver, take the screw off and pull out the battery that was in place. Then, you can insert the new battery and close the hole in the key fob.

Test the key fob by pressing the lock and unlock buttons. You're good to go in case the doors lock and unlock as expected. You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers start to get cold or you have to do some errands in Brandon.

Note: Some key fobs (transponder chip or smart keys) may require their programming done. This requires a specific programming machine that only the dealer or automotive locksmith has access to. Other keys (non-transponder metal keys) don't require programming. If you need to reprogramme your key, you'll need to note the key code number on the key code tag.

How to replace the battery

If the kia picanto car key replacement key fob does not respond when you press the lock/unlock button, it is likely that the battery is insufficient. A low battery may cause other issues, such as the check engine light appearing or the engine not working properly. Fortunately, replacing the key fob battery is a fairly simple DIY project that requires only the most basic tools.

Before you begin, make sure that your vehicle is off and all doors are closed. Locate the small plastic piece that is on the bottom of your key fob and play with it until a metallic key slides out. The key can be inserted into the driver door handle to unlock your car.

To replace the battery inside the key fob, you must remove the rear cover. Make use of a plastic pry tool to loosen the latch that holds the black negative cable. Remove the old battery, and then orient the replacement battery so that its "+" side faces you and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into place and avoid excessive force to avoid damaging or breaking the metal contacts.

Once the new battery is installed, turn the key fob off and on in the ignition for a few times until the door locks cycle. Then, test your Kia key fob to check whether it's working again.

How do you replace a keyless key

Depending on the model of your Kia Sportage, you may have an ordinary key fob or a smart key. The difference between the two is that the smart key is equipped with tiny mechanical key blade in it, whereas the standard key fob does not. Both types of key fobs have batteries that will eventually need to be replaced. It is a simple process which takes just two minutes.

Before you get started it is essential to ensure that you are on a level surface with sufficient lighting and that your Kia is not on. Be aware that there are tiny components inside the fob which could be snagged if not careful.

The release button for the small size is located on the lower backside. This will be either a circular or rectangular slot. You can open the key fob by pressing the button.

Once you have the key fob opened it is easy to take out the old battery and replace it. The new battery is one called CR-2032 and can be bought from a local or online auto parts store. Once you're done you should be able to lock or unlock your vehicle using your key fob - even if your engine isn't running!

How to replace a mechanical key

The Kia keyfob is a wonderful convenience that allows us to lock or unlock our car by simply pressing the button. Like any other device, the Kia key fob can have issues at times. There are ways to fix these problems and keep your key fobs working for many years.

A dead or low-quality battery is one of the most frequent problems. This could cause the fob to stop working completely or work intermittently. If this is the case then replace the battery with an entirely new battery.

If this does not solve the problem, use a flathead screwdriver standard to push the plastic casing of the fob open. Be careful not to scratch any internal components or scratch the plastic. When the battery is open, carefully take off the battery that was removed and replace it with a brand new one.

Once the new battery is in, close and then open the doors with the mechanical key (every Kia fob has an emergency mechanical key that can fit into the slot). Test the key fob to make sure it is working correctly. If the key fob isn't working, contact an expert locksmith or dealer to help solve the problem. Make sure they make you an emergency key that functions across all trunk and door cylinders in order to avoid lockouts again.