Repairs to uPVC Windows

uPVC is a great option for modern homes. They are easy to maintain and are durable and long-lasting. Unlike timber and aluminium, they are not susceptible to corrosion or rot.

It is essential to clean and oil UPVC doors and windows on a regular basis. This will help prevent costly repairs and improve energy efficiency.

1. Broken Glass

If the glass in your window has been damaged, it could cause a large amount of damage to your home, which can make it very hazardous and possibly fatal. You should take the time to make sure that your windows are in good condition.

For single pane windows it is relatively easy to replace them, and the replacement is usually able to fit into the frame that was previously installed easily. If windows with double panes are joined by internal beading, it is harder to remove and replace the old panes. In this instance it is essential to purchase plastic spacers in order to help the new pane fit into the window frame.

If you plan attempt to remove the window panes by yourself it is crucial to wear the appropriate safety equipment, including thick gloves and eye protection. It is also recommended to lay down a drop cloth before you begin working on the window panes so that any shards fall on the fabric, not onto the floor and could be trampled.

After the glass has been removed from the window, it's best to seal the gap with packaging tape or duct tape to block water and drafts from getting into the property until a professional can come out and fix the window. It also acts as an obstacle to stop criminals from getting into your home. If the gap is particularly large, you may think about the security door with an integrated window, since it will provide the best of both worlds.

2. Sagging

uPVC windows and doors are a cost-effective energy-efficient, durable and long-lasting alternative to timber sash windows. As time passes, they may develop a variety of issues such as sliding. A window that isn't properly aligned can cause problems with light, draughts, and even security. It's crucial to act as soon as you realize that your uPVC windows are falling down.

To fix a Window Repair that is sagging you can try repositioning the hinges. To do this, you'll need to open the window to get to the frame. With the screwdriver, you'll be able to remove the hinges at the top and bottom and adjust them by turning them clockwise or anti-clockwise. After you've repositioned the hinges, shut your window and verify the an appropriate fit. If you are happy with the fit of the window, you can tighten screws to hold them in the right position.

If you are unable to move the hinges, you may have to replace the seal. Seals made of rubber can dry out and lose their elasticity with time, leading them to lose their tightness. It is important to replace your seal as quickly as you can to keep your uPVC window waterproof and draughtproof.

uPVC handles could also loosen. This is usually due to screws that have become undone over time, but it could also be due to the handle mechanism wears out. It's fairly simple to fix a loose uPVC hand. First, you'll need to close the window and perform an initial fitting. The corners of the sash should align with the casing joint. If it doesn't then you can make use of a screwdriver to loosen the handle and then return the mechanism to its original position.

3. Water Leaks

It is important to take action if you awake each day to find a smoky wall and floors that are wet. The leaks of water through windows could cause structural damage to your home and also impact your ability to regulate the temperature of your home. The most common reason for leaking uPVC windows is that the sealant surrounding the frame is damaged or not present.

This is a simple fix that can be done by anyone who is a DIYer with the skills. Depending on how serious the issue is, old caulking may need to be removed. When it is time to uPVC repair, you should avoid over-caulking. This will make your window more difficult to clean and reduce its energy efficiency.

Verify that the drainage holes have no debris in them and that the sill pan is angled correctly to drain away from the window. In more serious cases you might need to consider replacing the window.

Moldy sills and rotten ones are other signs of water leakage. The fungus thrives in conditions of dampness and can spread quickly throughout the house.

If the leakage occurs between the double glazing repairs-glazed window, it is more likely that the issue is more with the seal than the frame. This can be easily corrected by a uPVC window specialist who will replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

Hinges could be the reason when your uPVC window is difficult to open or if it opens with the breeze. They can be easily replaced by any competent DIYer and are usually completed in just a few minutes.

Most households in the UK will have either top hung or side-hung uPVC windows that use hinges and, just like any mechanical component they can wear down over time. It is very easy to replace a hinge on a window, but it's easier if someone helps hold the frame.

Make sure that the uPVC hinges open and close in the proper direction. This can be done by checking for the arrows on each hinge. This indicates the direction in which the window should open.

The problem with the hinges on windows could be the result of incorrectly opening the window in a certain way or by inadequate installation at the factory. It is usually possible to fix the issue by sending us a photograph via our website and we will be more than happy to give you advice.

It is also essential to lubricate the hinges regularly. Applying a light engineering lubricant on the hinges is a good method to accomplish this. We recommend using a lubricant that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regularly lubrication will help the window operate and close more smoothly. It can also reduce the chance of windows sticking and prevent corrosion. This should be done at least once a year. WD40 or other solvent-based lubricants are not recommended as they could damage your uPVC windows.

5. Draughts

Draughts can be caused by several different factors. First, the hinges due to wear and tear can become misaligned, this causes gaps to develop where the sash meets the frame. These can be easily fixed by giving them a thorough clean, however when they're beyond repair, it might be necessary to have them aligned or replaced. The interlock may also become disaligned. This happens on the hinge's side and may need to be cleaned. In certain instances it is possible to replace them.

The next common reason for draughts are the window seals. They are susceptible to being worn out or damaged over time and allow air to escape through these gaps. Replacing these with high-quality weatherstripping will help to prevent draughts. Replace the windows made of upvc with low-emissivity glass. This will help control indoor temperatures and lessen the risk of draughts.

The last way to reduce the amount of draughts is to use a Draught-exclusion device. These are typically fabric tubes filled with a filler which can be placed over your window sill. They will keep your home warm by blocking cold air.

With a little maintenance and repair windows made of upvc will continue to provide excellent insulation and security for your home. It is important to remember that all windows eventually become worn out, and it is more cost-effective to simply replace them than to repair them. If you are experiencing issues with your Upvc windows, it's recommended to seek help from a professional immediately.