Peugeot 208 Key Replacement

It is recommended to leave the replacement of Peugeot keys for 208 to auto locksmiths equipped with the required equipment and skills. They can program and create keys more quickly and at a lower cost than a dealership.

A dead coin battery is most likely to blame the reason your key-fob stops locking or unlocking the doors. However, there are other reasons why the key might be malfunctioning.

Dead Coin Battery

A dead battery can stop your Peugeot 208 from locking and unlocking, as well as making it impossible to start the engine. In this scenario, you will need to choose the alternate method to start described in your vehicle owner's manual.

The spark plugs could also be worn out. The spark plugs are responsible for instigating the fuel that powers the engine. However they have a short lifespan. If they aren't used enough, they will eventually fail.

Fortunately, there's an easy solution for this issue. Check the voltage of the battery using a multimeter. If the voltage is lower than 11,5 volts, it's the time to replace it. It is also important to clean the battery's contacts if it has corrosion. This can be done by lifting the rubber covers that protect the two battery terminals and using wire brushes to clean any corroded areas of the battery. It is then time to reconnect the cables that connect the positive and negative poles.

Water Damage

If your 208 doesn't start and the battery is not running, then make sure whether the spark plugs are in good working order. You might find that they are dirty and do not spark. The spark plugs can be cleaned in the workshop.

Peugeot automobiles use keys that are transponder-type and integrates with the car's immobiliser system. This ensures that only the right key can start the engine. If the chip inside the Peugeot key is damaged, then it won't send the proper signal to the vehicle.

Water damage is a frequent cause of this problem. This is particularly prevalent in colder climates. the vehicle may have been exposed to rain or snow. In this situation, contact a reliable locksmith who will have the necessary tools and equipment to change the key's programming. They will also have all the latest technology and machinery required to make a Peugeot smart key. The process should take no more than 15 minutes.

Faulty Battery Contacts

Peugeot replaced the old transponder chips by introducing a new model that is based on electronic components mounted on a circuit board. This new system works well when it's brand new, but as time passes, the circuit boards begin to degrade and stop working properly.

This could stop the immobiliser chip activating which means that your car won't start. If this is the case it's a good idea to seek out a Peugeot specialist or locksmith.

Another issue that is common is when the battery for the key fob gets depleted, which causes the blade of the key to stop being able to feed into the lock. A locksmith for cars can replace the battery and cut a new blade for you, it's usually a simple fix.

Faulty Receiver Module

If your Peugeot key fob was not working after dropping it on the ground, being exposed to a sudden rain or accidently washing it or washing it, it could be due a malfunctioning receiver module. The receiver is responsible for sending radio frequency signals to the onboard computer, which is responsible for controlling the centralized locking system of your Peugeot vehicle.

Rubber seals on the key fob stop water from reaching its electronic chip. However prolonged exposure to water can penetrate these seals and damage the chip. The high salt content in the pool or ocean water could cause damage to the key fob when it is submerged.

If your Peugeot spare key fob stops working then you'll have to get the module replaced. This can only be performed by a professional auto locksmith or Peugeot specialist. peugeot 206 key replacement keys unlike other automobiles, are secured by an immobilizer system. This requires the right code to begin the car. This is why you must go with a knowledgeable Peugeot locksmith to take on the job of programming and creating a replacement.

Computer on-board is not working properly

The on-board computer of your Peugeot is responsible for a variety of systems in your car, including airbags and power windows. The on-board computer will show the code when something goes wrong. This code is stored in the system and stays there until the issue is fixed. This can often mean that the on-board computers to be replaced.

One of the main reasons for the airbag light coming on is loose or corroded connectors in the airbag sensor. This can occur due to wear and tear, aging, or exposure to moisture and salt. This issue needs to be addressed as soon as you can, since an airbag that is not functioning could be dangerous in case in the event of an accident.

If your Peugeot is showing a card detected as not present error then the key battery in the key fob might be dead or weak. This can prevent the key fob from transmitting a signal that will disable the immobilizer on your vehicle's standard. You can test this by pressing the unlock button on the key fob and then attempting to start your car. If this doesn't work then the battery in the key fob has to be replaced.