Peugeot 3008 Key Fob Problems

Peugeot's 3008 SUV, which is mid-sized, has a lot to offer. It drives well, looks good and has a surprising big boot. Can it compete in the most crowded segment of the market perhaps?

If your Peugeot keyfob does not work, it may have been exposed to clean or soapy tap water. You may need to take off the battery, clean it using isopropyl ethanol or electronic cleaner.

Dead coin battery

Peugeot key fobs are powered by the coin-sized battery. The power used to control the remote locking system as well as other functions. The battery has a limited lifespan and can get worn out after years of use. One way to determine whether the battery is defective is to perform an electrical test. Multimeters are used to measure the voltage between the poles that are plus and minus of the battery. The results of this test will indicate whether the battery is dead or not.

The receiver module may be the reason why your key fobs failing to function after having used your Peugeot 3008 for a prolonged period. The receiver module is in charge of receiving radio frequency signals generated by the key fobs and transmitting them to the car's systems. If the receiver module is in a fault, it won't be able send commands to the other modules in the car.

Sweat or moisture on the circuit board is a common cause of an unworking key fob. This can lead to short circuits that drain the battery, and also disable the remote locking feature of the key fob. If this is the case you need to bring your key fob in to a technician that specializes in chip level repairs.

Water damage

If you dropped your key fob into the pool, threw it into the wash or just put it in the rain for too long, water damage can be a real problem. Water is a good conductor, and it can cut off circuit boards. It can also cause corrosion to metal trace on the key fob and other components. A circuit board that is wet can also cause the battery dump its charge.

If you have an additional key fob, you can use it to unlock and lock the Peugeot 3008 to rule out a dead coin-cell battery as the cause of the problem. Another issue that can stop your key fob from functioning correctly is interference signals that interfere with the signal that is sent to the receiver module. These signals could come from a variety of sources such as radio transmitters in close proximity.

If you hear sloshing noises emanating from inside your peugeot replacement key fob 3008 when driving, it's most likely caused by a blocked condensate drain in the evaporator. You can test this by blowing compressed air through the drain holes under your door. You can also use a flexible wire to move the drain holes around and wash away any dirt that has built up there. Air pockets can be identified by sloshing sounds.

The receiver module is not working properly.

The receiver module of a peugeot car key replacement 3008 is responsible for transmitting an electronic remote keyless signal from the keyfob into the receiver in the car. The receiver module may be damaged and stop the car from acknowledging your key fob. Other causes of the issue include the battery being dead, water damage, or interference from electronic devices that operate at the same frequency the key fob. In these situations the car could display a message saying "card not detected" on the display.

There are many options to solve this issue. Try replacing the battery or reprogram the key fob. You can also start the vehicle with a spare key. If the key fob doesn't work after these steps, it may have a chip that is not working properly.

It is best to remove the chip and clean it using paper towels and rubbing alcohol. If the chip has been damaged, it is recommended to buy an entirely new one. FB Series enclosures are designed for key fobs and come with an additional coin battery holder that can fit the most common types of key fob batteries. The enclosures can be personalized with digital printing and CNC-machined cutouts. If your key fob has been exposed to dirty or salty tap water, your chip may be contaminated and must be cleaned.

Keyless entry systems that fail

If you see the message "card not detected", it means that your vehicle is unable to receive signals from your key fob. This can be caused by many different reasons such as batteries that are weak or dead. The issue is usually resolved by pressing the start button on the key fob. In certain cases, you might be required to take the keyfob to a Peugeot dealer for further repairs.

The first step to troubleshooting a Peugeot 3008 key fob that won't unlock or lock the doors is to check its battery. Batteries are often the main reason for a fob that is malfunctioning, but there are other factors that contribute to this issue as well. They include worn buttons, damage to the receiver module, water issues, and signal interference.

If your Peugeot key fob has been exposed to clean tapwater, it's recommended to remove the battery. Then dry the electronic components using paper towels. You can also use isopropyl alcohol or a cleaner for this purpose. It's best to change the fob if it has been exposed to salt or soapy water.

If your key fob is still not working, try to reset it by disconnection of the battery at 12 volts for about 15 minutes. Then reconnect the negative cable first, followed by the positive one.