fiat 500 key replacement 500 replacement key (www.saju1004.net website) Fob

If your remote key fob has stopped functioning, it could be time to replace the battery. If you replace the battery, but it doesn't work it could be the issue elsewhere.

United Locksmith specializes in the production of new keys for classic vehicles. We have the tools and parts required for this service.

Dead Coin Battery

A dead battery is the main cause of your Fiat 500 keyfob not locking or unlocking the doors. The battery for the coin cell in the key fob can be depleted quickly when you don't use frequently enough. If your remote began to show signs of weakness such as a loss in range and stopped working completely The battery is probably dead.

The battery inside the key fob is secured by metal clips that retain it. If the clips are not tight, they can cause contact issues that prevent your remote to receive power. Use a flathead screwdriver pry open the retaining clip and then remove the old battery. Make sure to select an identical replacement battery type of voltage, size and specifications as the original battery.

Water exposure can cause the key fob to corrode or become damaged. Even a small bath in warm, soapy water can damage the chip. Make sure your key fob is dry.

Water Damage

If your key fob isn't operating correctly, it could be due to water damage. The rubber seals on key fobs prevent them from getting damaged by a small drizzle or splash of water. However, it is important to keep the keys of your car away from the washing machine, ocean, and the pool.

The key fob has an electronic chip that sends a signal car's immobilizer system. The chip is what allows the 500 to be locked and started. If it gets wet it will cease to work.

You can clean the inside of your key fob's electronics using isopropyl alcohol or an electronic cleaner to determine whether they're still in good condition. However, it is probably best to get a replacement from a dealership instead of trying to fix the key fob that has been submerged by salt water.

While a replacement fob might cost you a little bit of money, it is a lot cheaper than having to pay for your Fiat 500 to be towed to the dealer and repaired! You can also do it yourself with only a few steps. Make sure you have the correct battery type before you attempt to open your key fob. This is a job that's more straightforward than it appears, and you can find step-bystep instructions online for nearly every key fob in your car.

Faulty Chip

The chip located within the key fob communicates to your car's immobiliser unit to make sure your car is only capable of starting when the correct key is inserted. If the chip is damaged, or damaged in any way your car will not start.

Damage to the water or a dead phone battery are among the most common causes of a faulty chip. It is best to hand over the job to a professional locksmith, who can replace the chip quickly and at an affordable cost.

If your key fob fails to function after exposure to clean tap water or rain, take off the battery and clean the electronic component with a towel to ensure that it is completely dry before putting it back in. If the key fob still isn't working it's probably a fried chip and will need to be replaced.

Some people will visit their dealer when they require a new Fiat fob. But, this can be expensive. If you are looking for a low-cost solution to have your Fiat key fob repaired then look no further than United Locksmith. We have all the tools and expertise to fix your Fiat fob quickly and professionally. way.

Faulty Receiver Module

Fiat key fobs transmit signals up 50 feet away to the vehicle, which will open and close the doors (and start the vehicle if it has automatic transmissions). There are many reasons why the fob could not function. It could be due to a dead battery or water damage buttons, worn out buttons as well as a receiver module problem and signal interference, or an electronic chip that has failed.

If the fob was placed in the pocket of someone who has suffered severe trauma (such as being dropped on the floor, or washed in the washer) the fob may not be able to communicate with the Body Control Module (BCM) of the vehicle. This is because the BCM is a secure system that will only accept a signal from a genuine original key and not another.

If this is the case, you will require replacing your fob. A professional locksmith is able to handle every aspect of the replacement process, including programming a new one for your 500. They can even provide you with a clone fob that works exactly like the original (and costs just a fraction of what it would cost).