How to Replace a Kia Sportage Replacement Key

For many Kia models keys, the key has the keyless entry system that is built into the key. This key usually resembles an electronic remote and can be replaced with a fresh one from a Kia dealer or a locksmith.

Key fobs can fail to function due to a number of reasons, such as batteries that are dead, worn-out buttons signal interference or water damage. Here are some helpful tips on how to get your Kia Sportage replacement key working again.

How to replace the remote key or smart key

The battery inside your Kia's smart key will eventually require to be replaced, whether it is a remote key or a push-to-start one, or a standard metal key that doesn't contain an electronic transponder. This is especially true if your car displays a message that indicates the smart or remote keys have low battery power.

It's a fairly simple procedure. To replace the battery on the keyfob remove your mechanical key from the slot at the back of the fob. Then, pry the cover open. A small screw will be found inside the key fob, which holds the battery in its place. Using a small screwdriver, loosen the screw and pull out the battery that was in place. Install the new battery and close the cut on the key fob.

When the key fob is equipped with an updated battery and you've tested it, press the lock and unlock buttons. If the doors lock and unlock according to your expectations, then you're set! You can now use the hands-free feature to lock and unlock your Kia whenever your fingers become cold or you need to run errands around Brandon.

Note: Some keys may require to be programmed (transponder chips or smart keys). This requires a machine for programming which is available to the locksmith who works for the automotive dealer. Other keys (non-transponder metal keys) don't require programming. If you want to change the programming of your key, you'll have to write down the key code's number on the key code tag.

How do you replace a dead battery?

If the Kia key fob does not respond to pressing the lock/unlock button, it is likely that the battery is depleted. A battery that is not functioning properly could cause other issues such as the check engine light coming on or delayed engine cranking. Fortunately, replacing the battery on the key fob is a relatively easy DIY project that requires just a few tools.

Before starting the process before beginning the process, ensure that your vehicle is off and all doors are shut. Find the small, metal or plastic piece that is on the bottom of your key fob, and move it until a metal key is released. This key can be inserted into the driver door handle to unlock your car.

To replace the key fob battery, remove the cover from the back and use a pry bar tool to remove the latch holding the black negative battery cable. Remove the old battery, and then orient the replacement battery to ensure that its "+" side is facing you and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into place, avoiding excessive force to avoid damaging or bending the contacts made of metal.

After the new battery has been installed, turn the key fob off and then turn it on in the ignition several times until the door locks cycle. Then, you can test your Kia key fob and see if it is working properly again.

How can you replace the smart key?

Depending on the model of the Kia Sportage, you may have a standard key fob or a smart key. The difference is that the smart key has an incredibly small key blade tucked inside it, while the standard fob isn't equipped with. Both kinds of key fobs come with batteries inside which eventually needs to be replaced. It's an easy process that only takes about two minutes.

Before you begin before you begin, ensure that you are on a level surface with adequate lighting and that your Kia is turned off. Remember that the fob can contain tiny pieces that could be thrown off if you're not careful.

The first step is to locate the small release button on the lower backside of your fob. It can be a circular silver button or a rectangular slot. After pressing this button, the mechanical key blade will pop out and you can then open the key fob.

After the key fob has been removed, you can remove the battery. The new battery is a one called CR-2032 and can be purchased through the internet or at a local auto parts store. After installation you should be able to lock, unlock and start your car with your key fob - even if your engine isn't running!

How do you replace the mechanical key?

The Kia keyfob is an excellent convenience that allows us to lock or unlock our car simply by pressing a button. But like any device there are issues with it at times. There are steps to take to fix these issues and ensure that our key fobs are in good working condition for the long term.

A dead or drained battery is among the most common issues. This could cause the fob to stop working altogether or even to stop working intermittently. If this is the problem it is time to replace the battery a new one.

If this doesn't solve the issue, use an ordinary screwdriver with a flat head to wedge the plastic casing of the fob open. Be careful not to scratch any internal components or scratch the plastic. Once the battery is removed then replace it with a brand new battery.

Close and open the door with the mechanical key. (Every kia key fob replacement fob comes with an emergency mechanical key which will fit into the slot). Test the key fob to ensure that it's working properly. Contact a dealer, or a locksmith to solve the issue in the event that the key fob is not working. Make sure they cut you an emergency key that can work in all the trunk and door cylinders in order to avoid lockouts in the future.