How to Replace a Kia Sportage Replacement Key

The key of many Kia models has the keyless entry feature built in. This key is similar to remote controls and is exchangeable by an Kia dealer.

Key fobs are prone to malfunction due to a variety of reasons, including batteries that are dead, worn buttons signal interference, water damage and a damaged receiver module. Here are some suggestions on how you can get your Kia Picanto Car Key Replacement Sportage replacement key to work again.

How to replace the remote key or smartkey

The battery in your kia picanto car key replacement's intelligent key will eventually need to be replaced, regardless of whether it's a remote key as well as a push-to start key or a normal metal key that is not equipped with transponder. This is especially relevant if your vehicle displays a message indicating that the smart or remote keys are in poor condition.

It's a fairly simple process. To replace the battery in the keyfob remove the mechanical key from the slit on the back of the fob. Then, pull the cover off. A small screw will be located inside the key fob to hold the battery in place. By using a small screwdriver take the screw off and remove the battery that was in place. Install the new battery and close the gap on the key fob.

Test the key fob by pressing the lock and unlock buttons. You're good to go when the doors lock or unlock as you expect. You can now use the hands-free feature to lock and unlock your Kia whenever your fingers become cold or you have to go on errands around Brandon.

Note: Some key fobs (transponder chip or smart keys) may require their programming done. This requires a specific programming machine that only the dealer or locksmith can access. Other keys (non-transponder metal keys) do not require programming. If your key needs to be programmed again, you will need to be aware of the key code number written on the key code tag and then record the number in a secure place.

How do I replace the battery?

If your Kia key fob is not responding when you press the lock or unlock button on the fob, it is a sign that the battery should be replaced. A low battery could cause other problems like the check engine light coming on or delayed cranking of the engine. Fortunately replacing the battery on the key fob is a simple DIY project that requires just some basic tools.

Before beginning the process be sure that your vehicle is turned off and that all doors are closed. Find the small metal or a plastic piece near the bottom of the key fob. Then, jiggle it until the metal key pops out. Then, you can insert the key into the door handle of the driver to open your car.

To replace the battery in the key fob remove the cover at the rear. Utilize a plastic plier tool to remove the latch that holds the black negative cable. Remove the old battery and align the new one so that the "+" positive side is facing you, while the "negative" negative side is facing towards the fob's electrical contacts made of metal. Push the new CR2032 battery straight into place and avoid excessive force to avoid damaging or breaking the metal contacts.

Once the new battery has been installed, turn the key fob off and back on in the ignition until the door locks. You can then test your Kia key fob and see if it is working properly again.

How to replace the smart key?

You can have a standard keyfob, or a Smart Key depending on the model of Kia Sportage. The smart key features an embedded mechanical key blade, unlike the standard key fob, which does not. Both key fobs come with batteries that eventually need to be changed. It is a simple process that takes less than two minutes.

Be sure to switch off your Kia and stand on a level, well-lit surface before you begin. Also, remember that there are tiny components inside the fob that can be snagged if not cautious.

The release button for the small size is located on the lower backside. It will be a circular button or a rectangular slot. You can open the key fob by pressing the button.

Once the key fob is open, remove the old battery. The new battery is a CR-2032, and can be bought online or in your local auto parts shop. When you're done, the key fob should permit you to lock, unlock, and start your vehicle even if it's not running.

How do you replace a broken mechanical key

The Kia keyfob is a great convenience that allows us to lock or unlock our car by simply pressing a button. Like all devices it is possible that the Kia key fob might have issues. There are ways to address these issues and keep your key fobs functioning for a long time.

A dead or weak battery is one of the most frequently encountered issues. This can cause your fob to stop working or operate intermittently. If this is the case it is time to replace the battery an entirely new battery.

If this doesn't solve the issue you can try using a standard flathead screwdriver to open the fob's plastic casing. Be sure not to damage any internal components, or scratch the plastic. After opening, carefully remove the battery you have been using and replace it with a new one.

When the new battery is in, close and then open the doors with the mechanical key (every key fob in the kia has an emergency mechanical key that will fit into the slot). Test the key fob to verify that it's working correctly. If the fob not working, contact an authorized locksmith or dealer to resolve the problem. Make sure they cut you an emergency key that functions for all trunk and door cylinders, to avoid lockouts in the future.