UPVC Window Handle Replacement

It's easy to replace a broken window handle with the right tools. However, it is essential to know the type of handle and the spindle's length prior to purchasing an alternative.

Older uPVC window handles have a spur that protrudes and locks on a wedge striker. They can be right or left-handed and have cost to replace windows uk be matched when replacing.

What kind of lock and handle do I have?

There are a myriad of window locks and handles made from upvc, each with its own advantages and Window Handle Replacement purposes. The type of handle you have will determine how easy it is to open your windows and if the locking mechanism functions according to the plan. With time and regular use the upvc handles that are on your windows can be damaged and worn out. This makes them less secure and less effective. In some instances, they could even fall off completely. If you find that your window handles have fallen off, it is essential to repair them as quickly as you can. This will stop possible burglaries and ensure that your home is secure.

It is a good thing that replacing your window handles made of upvc is a relatively simple task that is achievable by everyone. You'll require some basic tools, but with right knowledge, it is simple and should only take a couple of minutes. You will need to know the kind of handle or lock that you have on your window. This will allow you to choose the appropriate replacement.

Inline Espagnolette Handles

They are typically found on the sides of the window. They are flat in design and have a latch that connects to the locking mechanism of the window frame when it is turned. Inline upvc handles have spindles that run through the centre of the handle, and into the window frame to operate the latch.

Cockspur Handles

These handles are usually found on older uPVC window frames and have a distinctive, hook-shaped design. Cockspur handles are fitted with a single screw that holds the handle to the frame of the window and are not as secure as other kinds of window handles.

Tilt and Turn Handles

As opposed to the other upvc handles that are tilt and turn, these handles can be turned to open the window, and tilted inwards for ventilation. In general, they have a 7mm spindle at the side of the handle. They are available in left and right handed versions.

It is important to measure the spindle size when buying replacement upvc handle. Not all are the exact same size. To determine the length of your handle made of upvc, simply drop something into the middle of the hole, and then measure how far it extends before it comes into contact with an obstruction. This is the maximum spindle length that will fit in your window.

What is spindles?

uPVC window handles operate similar to doors, Window Handle Replacement by turning the handle to open an internal latch within the frame. The window is then opened and closed. However, in some cases, the handles may become damaged, especially if they are regularly used or exposed to extreme weather conditions. This can lead to the need to replace your uPVC handles for windows as they might not be able to operate the window properly anymore.

There are a variety of uPVC handles to choose from, including Espag, Cockspur and Spaded handle options. These handles are designed to fit in the uPVC frames in a variety of ways, and each type of handle has a particular spindle that is used to lock the mechanism into the window. It is essential to determine the kind of handle that is installed on your uPVC windows so that you can replace it with the right one.

You can check what type of uPVC handle you have by taking a look at the base of your handle. There should be a "snap in cover' over one screw that holds the handle's base in the correct position. Once you remove this and you'll be able to see the second screw that holds the handle base in place. After both screws have been removed, you should be able take the handle out of the uPVC.

After taking off the uPVC handle, remove it from the locking mechanism. Make note of the length of the spindle, as you'll need to ensure that you buy a replacement that has the same length as the original handle and locking mechanism.

The spindle wears out and is unable to operate the locking mechanism. This could be due wear and tear from continuous use or loosening of the locking mechanism or even corrosion over time. If this occurs, it will be necessary to replace the window handle and the locking mechanism to restore complete functionality to your uPVC windows.

How do I take off the old handle?

Window handles are susceptible to being damaged or destroyed over time. It is crucial to fix them as quickly a possible to ensure your safety. It is simple to replace a damaged or worn handle. The task can be accomplished in under an hour without the need of special tools.

The first step to remove the handle that was previously used is to take off the screw located on the top of the base of the handle. Once the screw has been removed, the handle will be removed. There is a second screw that is located at the bottom of the handle base, and it can be removed too. When both screws are removed the handle can be completely detached from the base section of the window.

After removing the old handle and align the fixing holes of the new handle with the holes that are already in the window frame. If there is a sticker or cap on the new handle remove it if needed and put the handle back in the appropriate position. It is essential to ensure that the handle works once it is installed. Turn the handle over and make sure the lock mechanism is working.

Espag handles come with a spindle that protrudes from the handle and slots into a multipoint locking mechanism within the window frame. Cadenza windows feature a blade with cut-outs that slot into the lock mechanism while Cockspur handles have a long nose that is able to hook over either the frame's outer or the transom bar cross member inside the window.

Once you have the new handle in place, insert the spindle into the lock inside the window and then tighten it. Once the handle is firmly fixed in place, replace the'snap in' cover and the screw cap (if necessary). The handle is now ready to use by opening and closing the window a few times to make sure that it functions well and securely.

How do I install the new handle?

Changing your uPVC window handle isn't a big deal and the process is actually very simple. All you need is a screwdriver and a small amount of patience. First, make sure that the handle that you are replacing is unlocked. Then, remove any screws that are visible. You can also replace them with screw caps. After removing the handle, you will need to note the length of spindle that extends from the back. This is crucial since it will determine the kind of handle you'll require to purchase.

Espagnolette handles are the most commonly used type of handle for uPVC windows. They have a spindle which runs through the handle and acts as an internal locking mechanism within the window frame. The handle opens the latch, allowing the window to open. During regular use and time, handles made of espagnolette can become damaged.

Cadenza handles are another type of uPVC window handle, which is typically used on tilt and turn windows. They have an extended blade that works an interlocking mechanism that is multipoint within the window. They are more secure than an espagnolette handles since they only open from the inside. They can be replaced by the same method as espagnolette handles but you should make sure that the new handle has a curved blade as opposed to one that is flat.

Once you have decided on the right handle for you, you can simply line up the new handle with the existing screw holes and then screw it into place. Then, put the screws back on and verify that the new handle is working properly. You can do this by moving the handle back and forth from the locked position to the unlocked several times. If you encounter any issues, it might be worthwhile contacting a professional to see if they are able to help resolve the problem. They can advise you on how to solve the issue in a timely and efficient manner.