Reasons Why Your Nissan Qashqai Key Fob Won't Work

The Qashqai has a distinct SUV-like feel due to its larger dimensions, and the wheel sizes of 19 inches in Ti and ST-L models may be a bit spongy at times. The front tyres may lose grip on rough surfaces and its CVT may occasionally exhibit wrist-flexing torque steer.

This is typically caused by the battery of a coin that is dead. It can be easily replaced in minutes. Make sure that the replacement battery has the same size, voltage, and specification.

Water Damage

One of the main reasons why a Nissan key fob displays the "key ID incorrect" message is due to water damage. The rubber seals on the key fob are designed to protect the chip's electronic components, however prolonged moisture exposure can cause it to not function properly. It is common to observe this if your keyfob was dropped into the ocean or swimming pool. It can also happen when it gets wet from showers or soapy hands.

If your key fob was exposed to water for the course of a long time and you're not sure, clean it using isopropyl or electronic cleaner. Or, it could require a visit to a specialist to repair or replace it.

If your key fob does need to be replaced, the procedure is relatively easy. First, make sure you have a multipack of the right battery (CR2032 3V). Then open the back and front cases using a small flathead screwdriver. Remove the metal clips, remove the battery that was in place and replace it. After reassembling the fob, put the mechanical key back in its place and make sure it works as expected. If it isn't then you'll have to take it to your local Nissan dealer or a professional locksmith to replace nissan key fob the chip in the key. Fortunately the chip isn't typically damaged by exposure to water and this shouldn't be a major expense.

Dead Coin Battery

Another reason why your Nissan Qashqai key fob may not work is because the battery for the coin is dead. The batteries typically last between 3-5 years, but they can become depleted over time, particularly when the fob is frequently dropped. You can replace the battery, but make sure it is the same voltage and the same size as the first. If you are using a different battery, it can cause the key to have an incorrect key ID which can prevent it from paired with your vehicle.

The best method to replace the battery on the Nissan Qashqai Key Fob is to pry it open with the help of a small screwdriver with a flat head. Push in the screwdriver in a small notch at the bottom of the fob and twist it gently to split the two parts of the key fob. Then, take out the old CR2025 button cell battery and replace it with another one after confirming its position on the fob.

Before putting the new battery in place be sure that there is no dirt or water damage to the terminals. If there is, clean the terminals using a small amount of isopropyl alcohol. Also, ensure that the pole cables are plugged in properly - they must be connected to the negative and positive poles of your battery, respectively.

Fault Diagnosis

If your Nissan Qashqai's main fob stops functioning after exposure to pure rainwater or clean tap water it could be a sign there's an issue with the internal chip. You'll require a new fob if you can't resolve the issue by replacing the battery. If the key fob didn't work after you dropped it, it's likely that the chip inside was damaged. It is usually possible to get the key fob to function once more if you remove and clean the chip using alcohol and paper towels and then put it back into.

Key ID Incorrect is a common mistake that you might see on the dashboard of your car. This means that the car is unable to recognize the key fob and not allow it to start the engine. The issue could be caused by a variety of things including water damage, undetectable issues in the circuitry of the key fob or RFID interference.

The key fob will stop working in the event that the 12 volt batteries are not working or provide sufficient electric current. This can affect your Nissan Qashqai's remote keyless system, central locking and the capability to start the engine using the key fob. If you're unable to lock or unlock the door by hand You should examine the batteries inside your key fob to be sure they're in good condition. Try reinstalling the battery to reset your transmitter.

Reprogramming

If the key fob was not submerged in saltwater it should be able to be revived with a simple rinse of clean water. You can also try cleaning the electronic chip with isopropyl alcohol or an electronic cleaner. If none of these works then it might be time to replace the entire key fob by a new one.

If your Nissan Intelligent Key is still not functioning, there may be an issue with the connection between it and the car. To reconnect it, begin by turning the key in the ignition but without starting the car. Keep doing this until you see the hazards lights flash twice. Turn the vehicle off and take away the keys.

Then, you need to open the fob compartment in your vehicle. It is usually located on a door jamb, or the handle of the driver's door. Find the small "program" button and press it. After the program is complete, you should hear a chime.

It's time to put your Intelligent Key to the test. Take a step away from the vehicle, and press all the buttons on it. If the lights flash and the horn squeaks it means the key has been successfully linked to the nissan juke key fob (relevant webpage). You may also try testing it close to the Nissan.