Repairs to uPVC Windows

uPVC is a great choice for modern homes. They are long-lasting, durable and easy to maintain. They don't rot or rust like timber and aluminum.

It is important to clean and oil UPVC doors and windows regularly. This will reduce unnecessary repair costs and also improve energy efficiency.

1. Broken Glass

The broken glass in your windows can cause significant damage to your home, and could even be fatal. You should take the time to make sure that your windows are in good condition.

Single-pane windows are fairly simple to replace and typically fit into frames of the past easily. If you have double glazed windows repair-paned windows that are held together by internal beading, it is difficult to remove and replace the panes that were previously in use. In this instance you'll need to locate some plastic spacers to aid the new pane in being able to fit properly into the window frame.

If you are going to attempt to remove the glass panes yourself, it is essential to wear appropriate safety gear, including thick gloves and protective eyewear. It is also an excellent idea to lay down a drop cloth before you begin working on the glass to ensure that any shards will fall onto the fabric rather than on the floor where they could be trodden under and cause further damage.

After the glass has been removed, it's a good idea to seal the gap with some clear packaging tape or duct tape to prevent drafts and water from entering the home until a professional comes out and repair the window. It also acts as a barrier to prevent any criminals from getting into your home. If the gap is large, you might want to consider using an alarm door that comes with an integrated window, as it offers the best of both worlds.

2. Sagging

Upvc is a long-lasting, energy-efficient and affordable alternative to timber sash window. However, over time they are susceptible to a range of issues like sliding. A window that is sagging can cause problems with light, draughts or even security. If you notice that your uPVC window is beginning to lose its shape, it is important to act swiftly to stop the issue from getting worse.

To fix a window that is sagging you can try to reposition the hinges. First, you'll need to open the windows to reach the frame. With a screwdriver, you can remove the hinges at the top and bottom and adjust them by turning them clockwise or anti-clockwise. Close your window to test the fit after having relocated your hinges. If you are happy with the fit of your window, you can tighten screws to keep them in place.

If you aren't able to move the hinges, you might require replacing the seal. Over time rubber seals can lose their elasticity and dry out, which causes their tightness to decrease. If this happens, it's important to replace the seal as fast as you can to ensure that your uPVC windows remain watertight and secure from draughts.

UPVC handles can also become loose. This is often caused by screws that have loosened over time, but it can be caused by the handle mechanism wears out. Fortunately, it's easy to repair the loose uPVC window handle yourself. The first step is to close the window and then perform a test to ensure that it fits. The corners of the sash should align with the casing joint. If it isn't then you can use a screwdriver to loosen the handle and then turn the mechanism back into the position it was in.

3. Water Leaks

It is important to take action if wake up every morning to discover mouldy walls and floors that are wet. The leaks of water from windows do can not only cause destruction of your home's structure but also hamper your efforts to control the temperature within your home. Most of the time, uPVC window leaks are caused by a damaged or missing sealant.

This is a relatively easy fix that can be completed by any competent DIYer. Depending on the severity of the problem is, the old caulking may have to be removed. When it is time to uPVC repair, you must avoid 'over-caulking'. This will only make your window harder to clean and reduce its energy efficiency.

Check that any drainage holes do not have debris inside them and Repairs to uPVC Windows that the sill pan is properly angled to drain away from the window. In more serious cases you might need to consider replacing the window.

Other signs of long-term water leakage are decayed sills and the appearance of black spots of mold on the wall near the window. The is a fungus that thrives in damp conditions and can quickly spread across the home.

If the leakage is occurring between the repairing double glazed windows-glazed window, it is more likely that the issue is with the seal rather than the frame. Again this can easily be repaired by a uPVC window specialist who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

Hinges could be at fault if your uPVC window is difficult to open or it blows open with the breeze. These are easily repaired by any skilled DIYer and can be done within a few minutes.

Like all mechanical parts hinges will wear out over time. It is very easy to change a window hinge however it is easier if someone helps you hold the frame.

It is also important to ensure that the uPVC hinges are opened and closed in the right direction. Check for the arrows on each hinge to determine which way the window should be opened.

Window hinges that aren't working properly could be the result of incorrectly opening the window a certain way or due to poor installation at the factory. Sending us photos through our website can often resolve the problem. We are happy to provide assistance.

Regular lubrication of the hinges is also necessary. This can be accomplished by applying a light engineering oil on the hinges, we recommend using a solvent-free lubricant such as 3-in-one Multi-Purpose Oil. Regular lubrication can make the window easier to open and close. It also decreases the risk of a window getting stuck and stop corrosion. This must be done at a minimum every year. WD40 and other solvent based fluids are not recommended since they can damage the parts of your uPVC window.

5. Draughts

Draughts can be caused by a variety of different factors. The hinges can also become disaligned as a result of wear, creating gaps between the frame and sash. If they're beyond repair, it could be necessary to have them realigned. Second, the interlock can be disaligned. This is located on the hinge's side, and could require to be cleaned. In some instances it might be necessary to replace them.

The next most common reason for draughts is window seals, these can become worn down or damaged over time and allow air to escape through the gaps. This can be prevented by replacing them with high-quality weatherstripping. Replace the windows made of upvc with low-emissivity lenses. This will help control indoor temperatures, and reduce draughts.

The last way to reduce the amount of draughts is to use a Draught-exclusion device. These are usually fabric tubes filled with a filler which can be put on top of your window sill. These will keep your home warm by blocking cold air.

Your windows made of upvc will keep providing excellent insulation and security to your home with a little regular maintenance and repairs. It is crucial to recognize that all windows have a life span and there may come an point at which it is more efficient to replace them than repair them. So, if you're experiencing issues with your Upvc windows, it is always recommended to seek assistance from a professional as soon as you can.