How to Replace a Kia Sportage Replacement Key

For a number of kia ceed key fob replacement models keys, there is an integrated keyless entry system. The key is usually akin to a remote control and can be changed by a new one purchased from an Kia dealer or a locksmith.

Key fobs may stop working due to a variety of reasons, such as a dead battery, worn-out buttons signal interference or water damage. Here are some tips to assist you in getting your Kia sportage replacement key working again.

How to replace the remote key or smart key?

The battery inside your Kia's smart key will eventually have to be replaced, regardless of whether it's a remote or a push-to-start one, or a regular key that doesn't have a transponder. This is particularly when your car displays a message telling you that the smart or remote keys are in poor condition.

It's a simple process. To replace the battery in the keyfob, remove your mechanical key from the slit at the back of the fob. Then, pull the cover open. A small screw will be found inside the key fob to hold the battery in the correct position. By using a small screwdriver take the screw off and remove the old battery. Install the new battery and then close the slit on the key fob.

Once the key fob has a fresh battery, test it by pressing the lock and unlock buttons. If the doors unlock and lock as expected, then you're set! You can now use Kia's hands-free lock/unlock function whenever your fingers get chilly or you have to do some errands in Brandon.

Note: Certain key fobs could need to be programmed (transponder chips or smart keys). This requires a particular programming machine that only the dealer or automotive locksmith has access to. Other keys (non transponder keys made of metal) don't require programming. If your key needs to be programmed again, you will need to be aware of the key code number that is stamped on the tag that identifies the key and record it in a safe place.

How do I replace a battery

If your Kia key fob is not responding when you press the lock or unlock button on the fob, it is a signal that the battery should be replaced. A low battery may cause other issues, like the check engine light coming on or the engine not cranking properly. Fortunately replacing the battery on the key fob is a simple DIY task that requires only the most basic tools.

Before you begin the process be sure that your vehicle is turned off and all doors are shut. Find the small metal or a plastic piece on the bottom of the key fob. Then, jiggle it until the key falls out. This key can be put into the driver door handle to unlock your car.

To replace the key fob's battery, remove the cover from the back and use a plastic bar tool to release the latch that holds the black negative battery cable. Remove the old battery and orient the new one so that the "+" positive side is facing you, and the "negative" negative side is facing the fob's electronic contacts. Push the new CR2032 battery straight into place with care to avoid using too much force to avoid damaging or bending the contacts on the metal.

Once the new battery is installed, turn the key fob off and then on in the ignition repeatedly until the door locks cycle. Then you can test your Kia key fob to determine whether it's working again.

How can you replace the smart key

You could have a standard keyfob, or a Smart Key based upon the model of kia keys replacement Sportage. The smart key has an embedded mechanical key blade, while the standard keyfob does not. Both key fobs are equipped with a battery that will eventually require replacement. Luckily, this is an easy process that takes just two minutes.

Make sure you turn off your Kia, and be on a level or well-lit surface prior to when you begin. Also, remember that there are tiny parts inside the fob that could be removed if not cautious.

The first step is to find the small release button that is located on the back of the lower part of the fob. This will be either an oval or circular slot. You can open the key fob by pressing the button.

Once you have the key fob open and you are able to remove the old battery and replace it. The new battery should be a CR-2032, and can be bought online or from your local auto parts store. Once you're done, your key fob should be able to lock or unlock and start your vehicle even if it's not running.

How do you replace the mechanical key

The Kia key fob is an amazing convenience that allows us to lock and unlock our car at the touch of a button. Like any device like a key fob, the Kia can have issues at times. Luckily, there are methods to resolve these issues and ensure that our key fobs are in good working order for the long run.

A dead or low-quality battery is among the most common problems. This can cause the device to stop working completely or stop working at times. If this is the case then try replacing the battery with a new one.

If this isn't enough to solve the problem, use a flathead screwdriver standard to wedge the fob's casing made of plastic open. Be sure not to damage any internal components, or scratch the plastic. Once open, carefully remove the battery you have been using and replace it with a brand new one.

Close and open the door using the mechanical key. (Every kia fob comes with a spare mechanical key that fits into the slot). Test the key fob to confirm it's functioning correctly. If the fob still isn't functioning, contact an expert locksmith or dealer to resolve the issue. Make sure they make you an emergency key that can work across all trunk and door cylinders in order to prevent lockouts in the future.