Peugeot 3008 Key Fob Problems

The mid-sized SUV from Peugeot, the 3008, has many positive points. It's stylish, it drives well, and has a big boot. Can it compete in the most crowded segment of the market perhaps?

If your Peugeot key fob isn't working, it may have been exposed to clean tap water or soapy water. You may have to remove the battery, clean it using isopropyl ethanol or electronic cleaner.

Dead coin battery

Peugeot key fobs include tiny coin batteries that powers their remote locking as well as other functions. The battery has a limited lifespan and is susceptible to wear out after years of use. Testing the voltage is a simple way to determine if the battery is not working properly. A multimeter can test the voltage between the battery's plus and negative poles. This test will reveal whether the battery is dead.

If you've been using your Peugeot 3008 for a while, and the key fobs have stopped working, there may be a problem with the receiver module. The receiver module is responsible for capturing radio frequency signals from key fobs and transferring them to the car's systems. If the receiver module has problems, it won't be able send commands to other modules within the car.

Sweat or moisture on the circuit board is another typical cause of an unworking key fob. This can lead to short circuits, which can drain the battery and disable the fob's remote locking function. If this is the case, you should take your key fob in to an expert on chip level to repair it.

Water damage

Water damage can be a problem, whether you dropped your keyfob in the pool spa, washed it or left it in the rain. Water makes for a good conductor, and it can also short out parts of the circuit board. It could also cause corrosion of the metal traces and other components on the key fob. A circuit board that is wet could also cause the battery to lose its charge.

If you have an extra key fob use it to lock or unlock your Peugeot 3008 to rule out the possibility that a dead coin battery is the root of the problem. Another issue that can prevent your key fob from functioning properly is interference signals that interfere with the signal sent to the receiver module. These interference signals can come from a wide range of sources including radio transmitters that are near.

If you hear sloshing sounds emanating from your Peugeot 3008 when driving it could be caused by a blocked condensate drain from the evaporator. You can test this by blowing compressed air into the drain holes under your door. You can also use flexible metal wire to wiggle drain holes in order to get rid of any dirt built up. Sloshing noises can also indicate that there are air pockets within the coolant system.

The receiver module is not working properly.

The receiver module on a Peugeot 3008 key fob is responsible for sending the remote keyless system signal from the key fob to the car's receiver. This module could be damaged and stop the car from accepting your key fob. This issue could be caused by an unresponsive battery or water damage. Or, interference from electronic devices operating at the same frequency. In these situations an error message such as "card not detected" may appear on the display.

There are many ways to resolve this problem. You may try replacing the battery or reprogramming your key fob. You could also start your car with a spare key. However, if the fob isn't functioning after these steps, it could have a chip defective.

The best way to know whether the key fob is equipped with an issue with its chip is to take it off and clean it up with a paper towel and rub alcohol. If the chip has been damaged, it is recommended to buy an entirely new one. The FB Series enclosures come with a coin cell battery holder that can be used with the most popular kinds of key fob batteries. The enclosures can be personalized by using digital printing or CNC-machined cutouts. If your key fob was exposed to salty or dirty tap water, it is possible that the chip is contaminated.

Keyless entry system that isn't working properly

If you see "card not detected", this indicates that your car isn't able to receive the signal generated by your key fob. This could be caused by a variety of reasons including a dead or weak battery. Most of the time, the issue can be solved by pressing the start button with the key fob. In some instances however, you might require taking the key fob to an Peugeot dealer for further repairs.

The first step in identifying the cause of a Peugeot 3008 key fob that doesn't open or lock the doors is to check the battery. Batteries are typically the cause of malfunctioning keys. However there are other reasons that could be involved. They include worn buttons, water damage, receiver module issues, and signal interference.

If your Peugeot key fob has been exposed to clean tapwater, it is a good idea for you to remove the battery. Then, dry the electronic components using paper towels. You can also use isopropyl Alcohol or an appropriate cleaner for this. It is best to change the fob after it has been exposed to salt water or soapy water.

If your key fob is still not working, try to reset it by disconnecting the battery with 12 volts for about 15 minutes. Connect the negative cable and then the positive cable.