Why Does My Rolls Royce Phantom Key Fob Not Work?

The Rolls-Royce Phantom is a luxury car that conveys wealth and status. Its huge grille that resembles waterfalls and the classic upright dimensions are instantly recognizable. It is one of the most expensive cars in the world.

The key fob for the rolls royce could stop working due to many reasons. A dead battery for the coin is the most common reason, but other causes include water damage or receiver modules.

Battery

The most frequent reason for a Rolls-Royce Phantom key fob not working is the dead battery within. It is essential to remember that the key fob may also stop working due other causes, like damaged buttons or water damage. Other causes include signal interference, damaged battery contacts, or unpaired keys which require the reprogramming. Speak with a locksmith if the key fob isn't working. A locksmith can diagnose the problem quickly and provide the solution quickly.

To ensure that the battery stays functioning, it must be protected from dirt and moisture. This is the reason why it is recommended to always use a case for your key fob that is waterproof while driving. It is also advisable to remove battery from key fob prior cleaning or washing it. Moreover, the chip in the key fob is extremely sensitive to water and shouldn't be exposed to salty or soapy water. If the key fob is prone to exposure to water, you can make use of isopropyl alcohol or an electronic cleaner to avoid water damage.

The battery pack of the Phantom EE includes a variety of new features which set it apart from the conventional power systems that are used in other luxury cars. For instance, the "power reserve dial" is now available on the dashboard, which conveys the car's energy status to the driver. This is a brand new design feature that is designed to challenge the traditional designs of cars and showcase the potential of alternative drive-train technology.

This electric powertrain has the benefit of allowing recharges without a physical connection between the vehicle and charging station. This is achieved through induction, which involves the transfer of power across two surfaces: an induction pad on the ground and an induction module underneath the battery pack.

The recharging process is done in two phases, resulting in a total charge capacity of 71kWh. Each phase has a capacity 13.5kW. This makes it the biggest passenger car battery in the world. The Phantom EE also comes with three separate chargers that can be used for single-phase and 3-phase charging, and regenerative braking.

Contacts

If your Rolls Royce Phantom remote key fob isn't working it could be caused by an inactive battery or worn buttons. Fortunately, the issue is usually fixable. You can also try reprogramming your key fob, or replacing the battery 12 Volt. If the issue persists the receiver module may be defective. The remote keyless system as well as other electronic components onboard use the receiver module to communicate with each other via radio signals. If the receiver module is damaged, it will stop to communicate with the key fob, or any other onboard electronics.

If you're experiencing issues with the key fob, it is essential to ensure that the battery contacts are dry and clean. The clips that hold the button cell in place keep the button cell battery in position and complete the circuit, and they can be damaged by dirty or wet hands. Replace the old battery with a newer version of the same voltage and dimensions. If you replace the battery, be sure to wash the surfaces of contact with the use of rubbing alcohol or electronic cleaner before rebuilding the key fob.

The key fob in the Rolls Royce Phantom is equipped with an electronic chip that transmits signals to the remote keyless system receiver module. The module then converts these signals into commands that the car can comprehend and respond to. This is how the car will know you're looking to unlock doors or retract the "flying woman" hood ornament in the grille.

If the key fob has been exposed to water, you should remove it immediately from the vehicle. Clean the chip with electronic cleaner or isopropyl. If you do not then, the chip could be damaged.

Water damage

The key fob comes with rubber seals that prevent the electronic chip from being exposed. This makes it immune to light rain and splashes but not the type of deep immersion that could happen if you drop your key in a puddle or drop it in the ocean. If the fob is damp, the chip may be fried. It is necessary to replace it.

Even if you've not dropped your key fob in water, but it's soaked by a wet dog or washing machine, or perhaps soapy handwashing, don't be discouraged since your phantom roll royce key fob may be usable. You can save money by following easy steps.

The first step is to remove the key fob and dry it thoroughly. Take the battery off If you are able, and use compressed air to blow any excess water out of the key fob. After you've completed this, allow it to dry for a few more days before using it.

If your key fob is prone to get wet, you should think about purchasing a waterproof case to protect it from accidents. It's also recommended to keep a spare key on hand to ensure that you don't need to wait around until the fob is dry out.

In some cases it is possible that your Rolls Royce Phantom key fob could stop working due interference or an unresponsive 12 volt battery. This is usually caused by objects, bad weather conditions, or transmitters which operate on the same frequency band as your remote.

The best way to prevent this problem is to keep your remote from these sources of interference. If you cannot eliminate these sources of interference, you can relocate your car to a new location or reprogram your remote. If you're still unable to fix the problem, it's best to seek out a professional technician. They will be able to identify the issue and determine whether it's mechanical or electrical fault.

Reprogramming

The key fob on your Rolls Royce Phantom plays a vital function in the security system of your vehicle. It transmits commands from the key fob to the receiver module which then sends the commands to the central locking mechanism of the vehicle. It can be a hassle and expensive if the key fob ceases to function. There are fortunately a few ways to get it back up and running.

Check if the coin battery in the key fob has died. It is a typical reason for Phantom key fobs that are not locking or unlocking properly and usually indications of wear and tear, for example a reduced range. Replace the battery with one of a fresh model with the same size, voltage, and specifications. Also, ensure that the clips made of metal that secure the battery aren't loosened.

Water damage is a different cause. The key fob has rubber seals that block water from getting to the chip inside. However, if it gets soaked in salty or soapy water, the seals could break down. If this happens, take the battery from the fob and clean it using isopropyl or electronic cleaner. Then, dry the battery thoroughly before putting it back in the fob.

If the key fob doesn't work it could be a sign the receiver module has been faulty. The best way to diagnose this is to connect a diagnostic scanner to the OBD port on the dashboard of your Phantom. The scanner will ask details about your vehicle, such as the year, model and type. You will also be asked to enter the code that was on your key fob.

Another possible cause is signal interference. This could be caused by objects, weather conditions or transmitters operating at the same frequency. The remote control will work when you are near the Phantom but not at a distance. You can try to fix this by removing any objects that might be blocking the signal, or by moving the Phantom away from the transmitters.