How to Replace a Kia Sportage Replacement Key

The key of a lot of kia picanto key fob replacement models has an electronic keyless entry system built into. The key can be compared to an remote control, and is able to be replaced with a new one from an Kia dealer or a locksmith.

Key fobs can stop working due to various reasons, such as the battery of the coin is dead, worn buttons signals, water damage, signal interference and a malfunctioning receiver module. Here are some tips on how to get your Kia Sportage replacement key to function again.

How do you replace the remote key or the smart key?

The battery inside your Kia's smart key will eventually need to be replaced, whether it's a remote key that starts with a push button or a normal metal key that doesn't have a transponder. This is especially the case if your car shows a message that states the smart or remote keys have low battery power.

Fortunately, it's an easy process. To replace the keyfob battery remove your mechanical key from the slit at the back of the fob. Then, push the cover open. A small screw will be located inside the key fob that holds the battery in the correct position. Take out the old battery by detaching the screw with the help of a small screwdriver. Install the new battery and close the slit on the key fob.

When the key fob is equipped with a fresh battery check it by pressing the locks and unlock buttons. You're good to go If the doors lock and unlock as expected. You can now use the hands-free feature to lock and unlock your Kia whenever your fingers feel cold or when you need to complete errands in Brandon.

Note: Some key fobs (transponder chip or smart keys) may require their programming done. This requires a machine for programming that is available only to the automotive locksmith or dealer. Other keys (non transponder keys made of steel), do not need programming. If your key requires to be reprogrammed, you will need to be aware of the key code number printed on the key code tag and record it in a safe place.

How do you replace a dead battery?

If the Kia key fob is unable to respond when you press the lock/unlock button, it's a sign that the battery is insufficient. A battery that is not functioning properly can cause other issues, such as the check engine light turning on or the engine not turning correctly. It is quite simple to replace the key fob batteries using just a few simple tools.

Make sure to shut off your vehicle and shut all doors before you begin. Find the small metal or a plastic piece on the bottom of the key fob. Press it until the metal key falls out. You can then insert this key into the handle of the door for the driver to open your car.

To replace the battery in the key fob, take off the cover at the rear. Make use of a plastic pry tool to remove the latch that holds the black negative cable. Remove the old battery and then orient the new one so that the "+" positive side is facing you, and the "negative" negative side is facing the fob's metallic electrical contacts. Push the new CR2032 battery straight into position with care to avoid using too much force to avoid damaging or bending the contacts made of metal.

After you have installed the new battery after which you turn the key fob off and on in the ignition until the door locks cycle. Then, test your Kia key fob to check whether it's working again.

How do you replace a smart key

You could have a standard keyfob or a Smart Key, based on the model of Kia Sportage. The smart key comes with an embedded mechanical key blade while the standard keyfob does not. Both key fobs contain an internal battery that will eventually need to be changed. It's an easy process that takes just two minutes.

Before you begin, you will want to ensure that you are on a level surface with sufficient lighting and that your Kia is not on. Be aware that the fob has small parts that can be thrown off should you not be careful.

The first step is to find the small release button on the backside of the fob. It could be an oval silver button or a rectangular slot. Once you press this the mechanical key blade will be released and you will be able to open the key fob.

Once you have the key fob opened, you can simply remove the old battery and replace it. The new battery is one called CR-2032 and can be bought through the internet or at a local auto parts store. After you're done, your key fob should permit you to lock and unlock your vehicle, even if it isn't running.

How do you replace a broken mechanical key

The Kia keyfob is a wonderful convenience, allowing us to lock or unlock our car with just pressing a button. But like any device it will encounter issues at times. Luckily, there are methods to fix these issues and ensure that our key fobs are in good condition for the long term.

One of the most frequently encountered problems is a low or dead battery. The fob could be able to cease working or to work intermittently. If this is the problem you should replace the battery an entirely new battery.

If this isn't enough to resolve the issue then try using a normal flathead screwdriver to open the casing of the fob's plastic. Be cautious not to damage any internal components or scratch the plastic. After the battery has been removed and replaced with a new one.

Close and open the door using the mechanical key. (Every kia fob comes with an emergency mechanical key which will fit into the slot). Test the key fob to ensure it's functioning correctly. If the device isn't working, call a dealer or locksmith to help resolve the issue. Make sure they make you an emergency key that can work across all trunk and door cylinders in order to prevent lockouts in the future.