Fiat 500 Replacement Key Fob

If your 500 remote key fob has stopped working, it's time to replace the battery. However, if you replace the battery but it is still not working the issue could be elsewhere.

United Locksmith specializes in the production of new keys for classic cars. We have all of the tools and accessories needed for this type of service.

Dead Coin Battery

A dead battery is the main cause of your Fiat 500 keyfob not locking or unlocking the doors. The battery for the coin cell in the key fob is likely to drain quickly if you don't use it frequently enough. If your remote began to show signs of weakness such as a loss in range and then completely stopped working, the battery is probably dead.

Metal clips hold the battery securely in the key fob. If the clips aren't tight, they can cause problems with contact that can prevent your remote from receiving power. Use a flathead screwdriver to open the retaining clips and remove the old battery. Make sure that the battery you choose to use has the same size, voltage and specification as the original.

Water exposure can cause the key fob to corrode or become damaged. Even a small bath in soapy, warm water could cause damage to the chip. Make sure your key fob is dry.

Water Damage

If your key fob isn't operating properly, it may be caused by water damage. Key fobs have rubber seals that stop them from being damaged by rain or a splash of water. However, it is crucial to keep your car keys away from the pool, ocean, and the washing machine!

The key fob has an electronic chip in it that sends a signal to your car's immobilizer system. This is the reason why your 500 can lock or start, but should the chip become wet, it will no longer work.

Try cleaning the inside of your key fob's electronics with isopropyl alcohol or an electronic cleaner to determine whether they're still functioning. However, it's better to purchase a new one from a dealer rather than trying to fix a key fob that has been submerged by salt water.

Although a replacement fob may cost a little money, it's far less expensive than having to pay for your Fiat 500 to be towed to a dealership and fixed! You can also do it yourself in a few easy steps. Make sure you have the correct battery type before you attempt to open your keyfob. This task is much simpler than it appears and you can find step-by-step instructions online for virtually any key fob in your car.

Faulty Chip

The chip located within the key fob communicates with the car's immobiliser system to ensure your car is only capable of starting when the correct key is inserted. If the chip is damaged or damaged in any way it will not start.

Water damage or a dead battery are the two most frequent causes of defective chips. Regardless of the reason, it's recommended to delegate the work to a locksmith as they will be able to replace the chip for you swiftly and at a reasonable cost.

If your key fob does not work after exposure to water that is clean from the tap or rain, remove the battery. Wipe down the electronic component using a paper towel. If the key fob does not work, there is an opportunity that it is malfunctioning components and need to be replaced.

Some people will go to their dealer when they are in need of a new fiat 500 keys key fob, however this can be a very expensive option. United Locksmith is the best option if you are looking to have your Fiat keyfob repaired at a reasonable cost. We have the tools and knowledge required to repair your fiat 500 key replacement cost fob in a timely and professional way.

Faulty Receiver Module

Fiat key fobs send an electronic signal to the vehicle that can unlock and close doors (and start the car for those with an automatic transmission) up to 50 feet. However there are several things that could cause the fob to cease working. It could be due to a dead battery or water damage or worn buttons as well as a receiver module problem or signal interference, or an electronic chip that is malfunctioning.

If the fob is in a pocket which has suffered a severe trauma, such as being dropped on a hard floor or getting washed in a washing machine and it isn't able to communicate with the car's Body Control Module (BCM). The BCM is a security device that can only accept signals from genuine original keys.

It is necessary to replace the fob if this happens. A professional locksmith will take care of the entire key replacement process including programming a new one for your 500. They can even provide you with an clone fob that performs the same as the original (and costs one-third of the price).