Repairs to uPVC Windows

uPVC is an excellent option for modern homes. They are long-lasting, durable and easy to maintain. In contrast to aluminium and timber, they don't get rusty or decay.

It is important to clean and oil UPVC windows and doors on a regular basis. This will help avoid unnecessary repair costs as well as improve the efficiency of energy.

1. Broken Glass

If the glass in your window has been damaged, it can cause a great amount of damage to your home, making it very dangerous and potentially fatal. It is important to take the time to make sure that you're doing all you can to ensure that your windows are in good repair.

For single pane windows, it can be relatively simple to replace windows, and the new one will generally fit within the frame that was previously installed easily. However, if you have double glazing repairs near me-pane windows that are secured by internal beading, it will be more difficult to take out the panes that are in place and replace them with new ones. In this situation you'll need to locate some plastic spacers that aid the new pane in being able to fit properly into the window frame.

Wearing eye protection and thick gloves is a must when you are planning to remove the glass yourself. It is also recommended to lay down a dropcloth before you begin working on the window panes to ensure that any shards fall on the fabric, not onto the floor which could cause them to be trampled.

Once the glass is removed, it's a good idea to cover the gap with some clear packaging tape or duct tape to block water and drafts from entering the property until a professional comes out and fix the window. It also acts as a barrier, deterring any intruders from getting access into your home. If the gap between the window and the door is large, you might need to consider security screens that includes an opening. This will provide the best of both.

2. Sagging

uPVC windows and doors are a cost-effective energy-efficient, durable and long-lasting alternative to timber windows made of sash. However, with time, they are susceptible to a range of problems including sagging. A sagging window in uPVC can cause issues with light, draughts and even security. It is crucial to act immediately if you realize that your uPVC windows are falling down.

To fix a window that is sagging you can try repositioning the hinges. To do this, you'll have to open the window so that you can access the frame. Then, remove both the top and bottom hinges with a screwdriver and adjust them counter-clockwise or clockwise. Close your window to check the fit after having repositioned your hinges. If you're satisfied with the size of the window, you can tighten screws to hold them in place.

If you can't reposition the hinges you may need to replace the seal. Over time rubber seals can lose their elasticity and dry out, which causes them to lose tightness. If this happens, replace it's essential to replace the seal as fast as possible to ensure your uPVC windows remain watertight and secure from draughts.

UPVC handles can also loosen up. This is often caused by screws that have been removed over time, but it can be due to the mechanism of the handle wearing out. Luckily, it's not difficult to repair a loose uPVC window handle yourself. First, you'll need to close the window and then perform a test fitting. The joint at the corners of the sash should align with the joint on the casing. If it isn't, you can use a screwdriver or a wrench to loosen the handle and reverse the mechanism back into the position it was in.

3. Water Leaks

It is essential to take action if you wake up every morning to find a smoky wall and wet floors. Leaks of water from windows can cause structural damage to your home, and hinder your ability to control the temperature in your home. The most frequent reason for leaking uPVC windows is that the sealant surrounding the frame has been damaged or not present.

This is a simple fix that can be accomplished by any DIYer who is competent. Depending on how serious the issue is, old caulking may need to be removed. It is essential to remember that when it comes to uPVC window repairs you should not be tempted to apply too much caulk and then make the area harder to clean and decrease the efficiency of your energy usage.

It is essential to ensure that the drainage holes are free of debris and that the sill pan is angled properly so that it drains away from the window. In more extreme cases, you may need to replace the window.

Moldy sills and rotten ones are also signs of water leakage. The fungus thrives in conditions of dampness and can spread quickly throughout the home.

It is also important to remember that if the leakage originates from the glass of your double-glazed windows, it's more likely to be an issue with the glass seal rather than the frame or sliding. This can be easily fixed by a uPVC window expert who can replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or are loose and blow open with a breeze it could be hinges that are at fault. These are easily repaired by any DIYer who is skilled and can usually be completed in just a few minutes.

Like any mechanical part hinges are prone to wear out over time. Changing a window hinge is essentially a very simple process but it can be easier to do if you have someone to assist in holding the frame in place.

Verify that the uPVC hinges open and close in the proper direction. Look for the arrows on each hinge to determine the direction in which the window should be opened.

The issue can be caused either by opening the window improperly or a faulty installation at the factory. This issue can be fixed by sending us a picture through our website and we will be happy to give you advice.

Regularly lubricating hinges is also essential. Applying a light engineering lubricant on the hinges is a great method of doing this. We suggest using a lubricant that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication can allow the window to operate and close more smoothly. It can also reduce the possibility of a window sticking and prevent corrosion. Ideally, you should perform this every year. WD40 and other solvent-based oils are not recommended because they could damage parts of your uPVC window.

5. Draughts

Draughts can be caused by different causes. The hinges can also become disaligned as a result of wear, causing an opening between the frame and sash. This can be easily fixed by giving them a good clean, but if they are beyond repair it might be necessary to have them realigned or replaced. The interlock, which is on the hinge side of the window, can be misaligned. Again, it may be possible to give them a good clean, but in some cases it might be necessary to have these replaced.

The seals may wear out or be damaged over time, allowing air to escape. Replacement of these with high-quality weatherstripping will help to keep draughts at bay. Replace the upvc windows with low-emissivity glasses. This will help to regulate indoor temperatures and decrease the possibility of draughts.

The final method to cut down on draughts effectively is by using a draught-excluder. These are usually made of fabric tubes filled with a filler which can be placed over your window sill. These will help to keep cold air out and keep your home warm and cosy!

Your windows made of upvc will remain a great source of insulation and security for your home by performing regular maintenance and repairs. It is important to remember that all windows will eventually get worn out and it is cheaper to replace them instead of fixing them. If you encounter any issues with your Upvc window repair near me you should consult an expert as soon as possible.