Fiat 500 Replacement Key Fob

If your remote key fob has stopped working, it may be time to replace the battery. However, if you replace the battery but it does not work, then the problem is likely to be elsewhere.

United Locksmith specializes in the creation of new keys for classic vehicles. We have all the tools and parts necessary to perform this service.

Dead Coin Battery

The most common reason your Fiat 500 key fob will not unlock or lock the doors is due to a dead battery. The key fob has an internal battery called a coin cell which will quickly drain if it is not used often enough. If your remote has started to show signs of a loss of range, or has stopped working or not responding, then the battery could be dead.

The battery in the key fob is held in place by metal clips that hold it in place. If the clips are loose, they can cause problems with contact, which can prevent the remote from receiving power. Using a small flathead screwdriver, push the clip that holds the retaining pin open to take out the battery and replace it with a new one. Be sure to use a replacement with the same type of voltage, size and specifications as the original battery.

The key fob might be damaged or corroded by water exposure. Even a quick bath in warm, soapy water can damage the chip. Keep your key fob dry.

Water Damage

If your key fob isn't operating correctly, it could be due to water damage. Key fobs are fitted with rubber seals that stop them from being damaged by light rain or a splash of water, however it is very important to keep your car keys safe from the pool, ocean, and washing machine!

The key fob comes with an electronic chip which sends a message to the immobilizer of your car. This is the reason why your 500 can lock or start, but if the chip gets wet, it's unable to longer function.

If you're interested in checking if your key fob is functioning, you can clean the internal electronics using isopropyl or electronic cleaner. It is best to replace the key fob if it's submerged in salt water instead of trying to repair it yourself.

While a replacement fob might cost a little money, it's much cheaper than having to pay for your Fiat 500 to be towed to the dealer for repair! You can also make it yourself by following some simple steps. Just make sure you have the correct battery type before you attempt to open your key fob. There are step-by-step directions for any key fob in your car online.

Faulty Chip

The chip located within the key fob communicates with the car's immobiliser unit to ensure the vehicle is only capable of starting when the correct key is inserted. If the chip is damaged or damaged in any way it will not start.

Damage to the water or a dead cell phone battery are the most frequently cited reasons for a faulty chip. Regardless of the reason, it's best to delegate the work to a locksmith since they can replace the chip for you swiftly and at a low cost.

If your key fob fails to function after exposure to clean tap water or rain, take off the battery and clean the electronic component with a paper towel to ensure it's completely dry before putting it back into. If the key fob does not function, there is the possibility that it's damaged components and requires to be replaced.

A few people will visit their dealer if they require a new Fiat fob. However, this can be expensive. If you are looking for a cost-effective way to have your Fiat key fob repaired make sure you contact United Locksmith. We have the equipment and know-how to repair your Fiat fob in a timely and professional way.

Faulty Receiver Module

fiat key replacement key fobs send signals up 50 feet to the vehicle, which can unlock and lock the doors (and start the vehicle if it has automatic transmissions). However there are some things that could cause the fob to cease functioning. It could be due to a dead battery water damage or worn buttons and a receiver module issue, and signal interference or an electronic chip that has failed.

If the fob is placed in a pocket that endured extreme trauma, such as being dropped on hard floors or being washed in a wash machine and it isn't capable of communicating with the car's Body Control Module (BCM). The BCM is a security device that only accepts signals from genuine original keys.

It is necessary to replace the fob in case this occurs. A professional locksmith can handle the entire replacement process including programming a new one for your 500. In fact, they could provide you with a replica key that works just the same way as your original fob (and costs less than the cost).