Patio Door Lock Repairs

Over time, patio doors experience wear and tear which can cause locks that fail. There are a few easy steps you can follow to ensure the security of your uPVC door.

It's about realigning the lock or cleaning the mechanism for locking, these quick fixes can increase the security of your home.

Clean the Lock

While patio sliding door repair doors are a great way to let the outside in and keep out the elements but they can also pose security risks if your lock isn't working as it should. Over time, wear and tear, hot and cold weather dirt and debris can take their toll on your patio door's lock and make it difficult to open. With a little maintenance, you can ensure your patio door's locks always perform properly.

To begin with, it's crucial to clean the lock of your patio door and all the moving parts. This will help remove any grime or coatings that might be hindering the lock from working correctly. Begin by wiping down all the moving parts of the lock for your patio door using a damp cloth. then make use of a scouring pad, or a rough damp cloth to scrub the hard-to-reach parts of the door and frame that are coated with dirt. It is recommended to wipe the entire lock with a dry cloth to remove any remaining dampness and allow it to air dry prior to using it again.

If you have an exterior door that is fitted with pin tumbler latch mechanisms it is possible to apply lubrication to the lock by applying powdered graphite to the key or applying a Teflon-based lubricant such as WD-40 Multi-Use Product. This type of lubricant is easy to apply and doesn't break down over time. If you are unable to find the correct lubricant for your lock, apply a pencil that has a thicker tip. Put the pencil into the lock and move it around a bit to spread the graphite.

Regular maintenance is also required to keep the tracks of sliding repairing patio doors doors free from dust, dirt and debris. These tracks are especially susceptible to ice and snow which can cause them be stuck or jammed, making it harder for your patio doors to open and close.

You can clean the track rails and rollers of sliding patio doors repair patio doors by removing damaged or dirty weather stripping. Clean it and replace it. The rollers of patio doors can be cleaned and sprayed with a nonstick lubricant.

Lubricate the Moving Parts

uPVC french doors, similar to sliding patio doors, operate using 3 to 4 or sometimes 5-point locking mechanisms that include the handle and lock cylinder operated by a key. They also require maintenance, and specifically lubrication of the moving parts. This can be accomplished using a thin oil (never WD40) and should be done every year.

If sagging hinges aren't a cause, the door could be misaligned and caught or striking the strike plate hole in the frame. The solution is to take off the strike plate, and then use a sharp chisel to enlarge the mortise it sits in. This will permit the latch to fit into the hole, and also prevent it from hitting the frame.

Take a measurement of the diameter of the cylinder using the help of a piece of book or wood that is able to fit into the space above the adjustment screw. The outer dimension is the distance from the outside of the door to the middle of the cylinder. the inner measurement runs from the center of the adjustment screw until the end of the cylinder.

Verify the width of the lock.

If your patio door latch is hard to turn even after oiling and cleaning it's possible that it's not aligned with the strike plate. Examine if the door is balanced and if the hinge screws are secure however, in many instances shifting the strike plate up or down can correct the issue.

The latch might not work properly when the strike of the lock is too small. In this case you'll have to increase the hole using either a hammer or chisel, and then test the latch to ensure that it contacts the strike plate in a smooth manner without rubbing against or catching on the door's frame jamb.

It is important to identify the type of mortise lock you are using before you purchase the replacement. This can be done by looking at the faceplate on the lock and determining whether it is round or square. Then, look at the screw holes in the existing lock and note the size of each one. This information will allow you to find a replacement lock that is exactly the same width and will fit in the hole that you already have.

You'll need to locate the mortise lock, and then examine it for scratches, bends or other damage that need to be repaired. A badly bent or damaged latch is more likely than one that has been used a lot to break. Replace the lock if it displays indications of damage.

After you've examined the lock and determined which kind of replacement you require, it's time to start working on the actual repair. The spindle and handle must be removed from the patio door. Introduce the new handle. Start by putting in the interior handle, aligning it with the spindle and then fixing it with the two bolts or screws that hold it. Install the exterior handle after the interior handle. Once you have completed these steps Test the handles to make sure that they open and shut easily and that the latch works correctly with the strikeplate.

Check the Strike of the Door.

The door latch and strike plate are the two parts of the lock that work together to ensure the latch secures the door. If they are not aligned properly and the latch doesn't latch the door properly. Fortunately, this problem is usually easy to correct.

Examine the holes that receive the strike plate to make sure they are free of obstructions like dirt or plastic plugs. Then, loosen the keeper screws that keep the strike plate in place and allow it to move vertically but not detaching it from the frame of your door. Then, adjust the strike plate to ensure that its receiving holes align with the latch hooks on the door latch. Once the strike plate is adjusted, tighten the screws and test the door to determine if it shuts smoothly with the new adjustment.

Door strike plates can be difficult to access for homeowners with sliding patio door repair near me patio doors, company however they're essential for locking and unlocking your door. The metal plates are situated at the top and bottom jambs of the door, which are where they help support the latch. The door latch slides into the strike plate and forms a seal. If the strike plate is damaged or rusted, or if it is not properly installed the latch may not be able to lock the door properly.

One common reason for an outdoor door lock to stick or not close is a misalignment between the latch and the strike plate. This can be confirmed using the "lipstick" test. Apply some lipstick across the edge of the deadbolt, then cover it with masking tape. When you shut the door the lipstick will leave an impression on the tape, showing exactly where the latch contacts the strike plate. If the mark is too high or low it is possible to alter the strike plate.

The sliding patio door locks protect your home from burglars. If they're not working correctly, you should solve the issue fast. By following these simple steps, you can repair your double glazed patio door repairs door's lock and restore its functionality in no time.