Electric Fireplace Wall Hanging Ideas

Unlike traditional gas or wood fireplaces Wall-mount electric on wall fireplace fireplaces are ready to be installed straight out of the box. These fireplaces can be a great way of adding the ambience of your home without the need for renovations or venting.

They are usually heavy and require careful installation. Follow these steps to hang your new electric fireplace properly.

1. Connect the Brackets

A wall-mounted electric fireplace or recessed fire instantly transforms any space. It's the ideal solution for homes without an existing fireplace opening or for apartment living.

First, you must decide where to put your new electric fire. You should choose a place that is not susceptible to moisture, and at least just a few feet from furniture and drapes. Once you've found a spot you like, mark the wall with markings for the top and bottom plates of the fireplace frame.

Make use of a tool like a drill to make exploratory holes into the wall, examining for studs with a detector and marking the drywall for the fireplace mounting bracket locations. Next, patch and paint the drywall or create a wall to prepare it for fireplace installation.

Depending on the wall-mounted fireplace, you could be required to install the screen and firebox as one unit or separate them by a wall bracket. If you're not sure about your ability to finish this project you can hire a general contractor or an experienced carpenter.

You can find templates included with the majority of electric fireplaces. However you should keep a spirit level handy and a pencil to mark out the exact spot where the wall brackets will be placed. Before drilling, use the template to check that the power cable of the fireplace can be able to connect from the installation site to a nearby outlet for a plug-in that is convenient.

Once the studs and the fireplace frame are in place, you can then install the drywall as seamless and flush as is possible for a clean appearance. Add a piece of trim to the bottom edge and then sand and paint the entire frame for an attractive look.

Most wall-mounted electric fires have hooks or slots on the back of the unit which you insert into slots or hooks on the mounting brackets. Make sure the slots or hooks are aligned prior to when connecting the fire to the wall brackets. Once the fire is set you can add additional elements, such as crystal embers, driftwood log pieces, or decorative rocks.

2. Check the Bottom Bracket

The space above the mantel, fireplace, or chimney breast is ideal for hanging artwork. However, there's a fine line between an artistic arrangement and one that is distracting from the overall design of the fireplace design.

Generally, the rule of thumb is that a picture should be about 80 percent the length of the fireplace or mantel it sits above. This will help keep it in proportion and look great on the wall. Other decorative ornaments and accessories placed on the mantel could influence the size and proportional guidelines.

If you are planning to display a photo above your electric fireplace the frame must be constructed of glass or a material that is able to withstand high temperatures. If you're not sure, a quick test with a temperature-sensitive cloth will show whether the frame is suitable for this type of use.

The most common issue with the display of artwork above the fireplace is the possibility of damage to artwork due to smoke or stray heat. This is not an issue with a wood- or gas-powered fireplace. However when you are planning to use an electric wall fire it is important to read the instructions of the manufacturer.

Most electric fires come with an installation bracket that can be fixed to the wall hanging electric fires with either hanging screws or wall-mounted fixing systems. It is recommended to make an exploratory hole in a discrete area of the wall prior to putting up your electric fire. Afterwards you can use a pipe & cable finder to verify whether there are any cables or pipes near the position you've chosen for mounting.

If you have a problem, you can then decide to put your fire above the electrical socket, or move it to a different spot. If you choose to move it to a new location, you'll need to ensure that the power cable will extend from the fire to the electrical socket. this is especially important for older houses or homes with solid walls. If not the electric fire will not perform as it should. Certain models have a template included that shows you where to drill holes to make the holes and others require a spirit level and pencil to mark the appropriate places on your wall.

3. Connect the Power Cord

If you've installed a recessed electric fireplace that hangs on wall fireplace, you may have to move the plug socket from the wall to behind the unit. This can create a sleeker appearance. Check the fireplace first to make sure it works correctly.

Another method of mount an electric fireplace is to frame the space and build it into the wall. This gives a finished traditional look and also allows you to add an additional mantel. The owner's guide for your model will include information on framing, wiring, and securing the fire.

When you're ready to install your new electric fireplace on the wall begin by marking the installation location with a pencil or marker. Then you can use a carpenter's degree to ensure that the location is level and flat. You can also employ a stud finder to mark the location of studs, so that you can be certain that you're drilling into an area that is safe.

After you've marked the location for installation and marked the location, use your drill to create holes for the hanging screws or bracket screws. Follow the instructions in the owner's guide to this step. This is especially important if you are installing the fireplace into drywall. If you're not sure what to do, Electric Fireplace Wall Hanging you can ask a professional for help.

You can also conceal power cords from view using cable organizer kits. These kits usually include clips, sleeves or boxes that can be used to bundle cables. You can also make use of fish tape or wire snake tools to guide the cords through the wall. If you'd rather not cut into your wall, you can install an electric bridge kit to make more secure and safe connections.

You can also camouflage cords using paintable wire covers or by attaching them to the wall. Be sure to keep the cover or tacks away from the source of heat, however. This will shield the cord from damage and also prevent accidental contact.

4. Connect the adapter

A wall-mounted electric fireplace is an excellent option to make for home improvements or those who do not have the space or money to put in a gas fireplace. They are easy to hang and are ready to use straight out of the box. They're a great alternative for those who want an elegant, modern design or warmth from a fire. They are designed to be hung like art on any wall. They can be recessed or not recessed at all and are fully electric wall mounted fire place and Electric Fireplace Wall Hanging have heating that is powered by a fan.

Before you start the actual installation process it is recommended to make a list of all the equipment and tools you'll need. There are detailed instructions on how to install an electric fire in the user manual. Certain models require you to screw brackets directly into the wall while others may feature an installation plate that slides into slots or hookeds on the brackets. If you're installing a recessed unit it is important to ensure that all combustible materials are taken from around the installation area. In general it is recommended to keep these items at least 3 feet from the front of the fireplace.

After you've checked all components, you need to plug in your electric fireplace and make sure that it works correctly. This is a crucial step to ensure the flame effect screen and heater operate as intended. This will also give you an idea of how the finished product will look in its final position.

Cover the cord once you are satisfied that it is working properly. This will help to keep the finished product neat and neat. You can do this by using paintable wire covers or you can choose to install a new outlet that allows you to place the cord behind the unit. This will give your fireplace a seamless look.