Reasons Your Fiat 500 Key Fob Won't Work

A Fiat 500 key for fiat 500 fob allows you to easily open doors and start your car. There are many reasons the fob may stop working. These include a dead coin battery or damage to the receiver module, water issues, and interference.

This listing is for a NEW replacement Fiat Flip Key Remote - look-alike Ilco brand that needs to be programmed professionally by a local locksmith (click here to search for a Locksmith Search). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the main reason for your 500 key fob not working. Modern key fobs come with a limited operating range and should be within just a few feet of the vehicle to operate. If you're far from your vehicle and press the key fob button the car won't respond, and will display the "Key Fob Not Detected" message in the instrument cluster.

If this happens If this happens, replace the battery in the coin-cell (Part Number CR2032) by a brand new one of a reliable brand, such as Panasonic Duracell or Energizer. They are typically available at your local hardware store, or online.

After you've replaced the battery of your coin cell You can test it by standing close to your fiat 500 key replacement cost (mouse click the next web site) 500 and pressing the buttons. The car should flash its parking lights, and the key fob will operate the lock and unlock buttons.

If the fob's remote doesn't work after replacing the battery, it may be damaged by water that blocks it from communicating with the receiver module in your car. Water damage can occur in a variety of ways, ranging from a light splash to submerging the fob into salt water at the beach. If you suspect that your fob has been exposed to water, try placing it in a dry rice bag to pull the moisture back out. If this does not work, you'll require your fob to be changed by an auto locksmith or a dealer.

Water Damage

Damage to the water supply can occur if you immerse the fob into the ocean, or wash it in a washing machine. Saltwater can cause the circuit board to short and eventually die. The fob getting wet is not an option, but if you drop it into a cup of water or do not remember to remove it from your pants pocket prior to running the washer, don't give up hope.

First, remove the battery from the fob. Clean the electronic chip using isopropyl alcohol or a similar product and dry it completely before replacing the battery. Next test the fob to check if it functions. If the key does not function it could need to be reset. This is typically done by a dealer or professional auto locksmith.

If the key you have is older and not programmed for your vehicle, you will need to replace it completely. A professional locksmith for cars can do this job. The locksmith will require the key cut to match your vehicle's ignition. They'll also need to reprogram the fob for the system of your car. This is a cost-effective and fast process that can be completed in the same day.

Receiver Module Issues

Your 500 key fob may not work because it's out of range. The remote's range is of 30 feet. Therefore, if you are too far from your vehicle it will not respond to your commands. It can be solved by moving it closer to your vehicle until it starts responding.

If you've replaced your coin battery (commonly known as"button" or "button" or "watch") and your fob doesn't function It could be because of an internal circuit board issue. In most cases, reprogramming the fob will resolve this issue. You can find the instructions on how to do this for most automobiles by searching YouTube or checking out the owner's manual.

You may need to replace the metal clips that keep the coin battery. If they become loose, it can stop your coin battery from sitting properly and cause your remote to malfunction.

In rare cases the fob may be out of alignment with your vehicle because due to hardware or software issues. This issue can be fixed by visiting your local dealer or auto-locksmith to reprogram your key fob. In certain instances the software might require reinstallation to your body control modules.

Interference

Interference can also cause the key fob to not receive or transmit a signal. This could occur if the keyfob is located in close proximity to a radio transmitter, such as a cell phone or radar detector. The key fob could not function due to a bad connection to the buttons, water damage or damage to the internal chips.

If your key fob suddenly stopped working, or you've tried everything at home to fix it (e.g. You might have a damaged 500 receiver module in the event that you've tried replacing the battery, reprogramming, or using a spare key fob. The receiver module, located under the dashboard, is able to pick up radio frequency signals from your key fob. It converts them into electronic commands that the vehicle interprets.

Luckily, there is an easy way to reset every single system on board in your 500 and include the key fob. Disconnect the battery for 15 minutes, removing first the negative cable, then the positive cable. Then, reconnect the battery. This will clear any residual electricity, and restart the computer of your car. This will help you get your key fob working again. If the issue persists, you should seek out an expert technician. They can identify the exact cause of issues.