Bentley Continental Key Fob Troubleshooting Tips

The Bentley Continental is a truly stunning car to drive. The center stack is embellished with polished metal, while the interior is adorned with beautiful wood and leather. Its formidable W12 engine generates 552 break horses of power.

The Continental key fob features rubber seals that prevent water from destroying the electronic chip. If it is submerged in water from rain or clean tap water, it will be fine. However long exposure to saltwater can harm it.

Keyless entry system

The Bentley Continental comes with a keyless entry system, which allows you to lock and unlock your car with remote control. This is convenient, and you will save time. However, there are several reasons for why your key fob might not work. One of them is a dead battery, water damage or receiver module issues. In certain cases a malfunctioning internal chip could be the root of the problem.

The key fob is encased with rubber to keep water from entering the electronic chips. However, the key fob can still be soaked if exposed to salt water or soapy water. This could cause damage to your chip. It is crucial to clean the key fob thoroughly and let it dry completely before replacing the battery. If the keyfob doesn't work after cleaning and letting it dry, then it's probably defective and requires replacement.

The battery of your Continental key fob features clips made of metal that hold it in place and complete the circuit. Contact problems can occur if the clips are corroded or loose. Make sure to check the battery's contacts to ensure they are clean. Also, make sure that the battery is properly installed. Test with a spare Continental Key to determine whether it functions. If the key is defective, you can reprogram it using an OBDII scan.

Battery

The key fob is equipped with a tiny coin battery within. When it is dead, the remote won't work. This is a simple issue to identify and is fixable in just a few minutes. Water can also damage the battery, requiring a replacement. The key fob might not function for a variety of reasons, including worn out buttons, faulty contacts in the battery, signal interference or an inactive module. The system can be reset by disconnecting the 12 volt batteries for a few seconds. This will allow the system itself to reset. Remove the negative cable first and then reconnect the positive cable.

The battery in the bentley valet key Continental key fob will last for four years based upon how frequently you use it. The battery is secured by metal clips. The clips must be secure but if not, the remote will not function properly.

If the Continental key fob is exposed to clean tap water, it should be cleaned with a paper towel and dried before putting it back into the battery. If it is exposed to soapy or salt water, the chip may be fried. In such cases you'll need to buy an entirely new key fob.

Water damage

David believes there aren't any major mechanical issues on this Continental car, besides small amounts of rust on the wheel trims and some surface corrosion in areas exposed to road grit. The boot is large and practical with a factory-issued warning triangle that is strapped to floor and a space-saving spare wheel, as well as the basic Bentley Toolkit on the false floor.

The chip on the key fob is protected by rubber seals which will ensure that it functions even when it's soaked. However prolonged exposure to water could damage the chip, so it's advisable to take your key fob out of your purse when you go for a swim, kayaking and rafting, canyoning or any other activity in which it could be wet.

If your key fob has been submerged in soapy water from the washing machine or submerged in ocean water at the beach, it could be worth attempting to get it back by cleaning the chip using isopropyl ethanol or electronic cleaner. If your key fob does not work after drying and cleaning you might need to replace it. If you're in search of a Bentley Continental Key Fob, be sure that it's water-resistant, factory-paired to your vehicle.

Fault diagnosis

The Bentley Continental keyfob lets you to lock or unlock your car in just one click. This system is convenient and gives you security and safety when driving. However there are a few things that can be wrong with your key fob. The most frequent causes include a dead coin battery or water damage, signal interference, and a faulty internal chip. If the key fob you purchased isn't working there are a few troubleshooting actions you can follow to identify the problem.

The first thing you need to look at is the battery. Make sure it's properly inserted and the retaining clips made of metal are positioned correctly. If the clips are loos and the battery isn't get a good connection and will not work correctly. Also, the retaining clips must be free of corrosion.

A weak car battery is a different reason for the key fob not to function. The battery that powers 12 volts in your Continental should be in a healthy state to be able to communicate with the remote keyless entry system as well as the rest of the electronics onboard. Check the fuses and should they be needed, recharge the battery.

The Bentley Continental key fob sends a signal to the receiver module which is located inside the ignition barrel. If the signal is lost the engine will not start and the alarm will sound. If the Bentley Continental key fob isn't working, you should speak with a professional.