Choosing the Right UPVC Door Handle Replacement

Replacing the handles on your doors made of upvc is a relatively simple job but picking the right handle can be a challenge. Modern double-glazed handles are equipped with spring cassettes, whereas older handles do not.

If the handle of your upvc is loose and floppy there may be an issue with the internal components of the multipoint lock. This article will address a variety of potential problems and their causes.

Handles that are drooping or sagging

UPVC handles can withstand wear and tear, particularly in older properties. A broken spring cassette in the door lever is the most common cause of a floppy handle. This is due to excessive force, and the square spindle holding the cassette can be moved or turned round.

The good news is that a uPVC door handle replacement is a relatively simple job and can be completed in a matter of minutes. The first step is to take off the old handle unit. To remove it, loosen the fixing screws visible on the back of the handle lever. Once the handles have been removed, you can unscrew and replace the cassette.

You can find a vast range of uPVC door handles to pick from on the internet and a lot of them are available in various finishes. Selecting the right finish will determine the length of time the handle will last and how easy it is to keep clean. Finishes like PVD, Stainless Steel or Resista are designed to resist corrosion and will last for up to 25 years.

After choosing a color or design, you can choose the type of handle you require. The most popular are lever and pad arrangements. Lever pads are equipped with a lever inside and an outside paddle and are often employed as a security measure to prevent unauthorised access.

Then, you should measure and note the dimensions of the handle you currently have. You'll need the PZ dimension (the distance from the screw hole to the middle of the lever) and the length of the handle as well as the dimension of the keyhole. You can compare these measurements to the size matrix of the handle to find the right replacement.

Broken springs

Over time, uPVC door handles may become wobbly or loose and at times the spring cassette inside might break. The tiny springs move the lever to a horizontal position. without them, your doors won't lock properly.

Modern uPVC handles come with these cassettes built into the back plate. However, older uPVC doors typically include these springs in the lock mechanism. This can't be fixed on your own, but it's worth asking your locksmith to take a look at as this could be the cause of the drooping or sagging uPVC door handles.

The most common problem associated with uPVC handles is that they tend to loosen as time passes. This is usually due to worn-out springs, which are simple to fix. Most often the reason for this is excessive use of the handle and because of that the square spindle inside the handle will wear away and cause the springs to be displaced.

In order to rectify this issue, open the door and remove the fixing screws on the back of the handle plate. This can be accomplished using the help of a Philips screwdriver. Once the screws are removed, the handle can then be removed. The plates for the handle can then be taken apart. Then, you can remove the old springs and replace them with new ones.

It is crucial to keep this in mind when purchasing a replacement handle. This measurement is known as the PZ measure and it is recommended that this is done using a calibrated tape measure in order to be accurate.

After replacing the springs you should be able operate the handle with no problems. However, it's always worth lubricating the mechanism inside to ensure that everything functions just as it should. This will not only ensure that your uPVC doors are as secure as they can be but also makes them more comfortable to operate in the long run.

Handles that slide around

Handles that slide could be caused by many things. One of the most frequent causes is when the levers of the handle aren't aligned with the lock. This is a problem that can occur with both uPVC and composite doors, but is typically more evident on older doors as they are usually made of less durable materials that don't hold up to the elements.

This issue can be fixed by a professional who will realign the handles and make sure they're in line with the door lock. They will also check the lock to see whether anything is required to be fixed. In many instances, a minor tweak to the handle springs is all it takes to resolve this issue.

It's simple to replace your uPVC handle however, you must measure the handle that you are replacing to ensure that the replacement is of the right size. You will need to measure the distance of two screws, the dimensions of the keyhole and lever, and the distance between them. You can then make use of this uPVC handles size guide to find an appropriate replacement for your home.

Once you have the measurements then the next step is to eliminate the existing uPVC handles. It is usually a simple procedure and requires only a screwdriver. Once the screws are removed, you will need to remove the handle and then install the new one.

It is important to secure the door using a wedge prior to starting. This will stop it from closing during the course of your work. After you remove the handle, you can inspect the components underneath the door that cause the door to slip.

If you don't have the time or nerves to tackle this job yourself, a handyman from Fantastic Services can help. They will employ specialist locksmith opening techniques to unlock the door without causing damage, and then replace window handle the damaged handle, making sure everything is working exactly as it should.

Gearbox damaged

A damaged gearbox can cause the upvc door handle to become stiff or lose its function. The lock may also be unable to be opened with keys. This could be extremely dangerous and should be dealt with as soon as possible. It is important to call an expert locksmith if you can't solve the issue on your own. They have the tools and expertise to complete the task correctly.

The first step is to remove the handle for patio door from the cover plate. You can do this with the help of a screwdriver with an angled tip. After you have removed your handle, you are able to remove the middle screw that holds the cylinder in place. After removing the middle screw, you will be able to loosen the two screws which are holding the barrel. You can then pull the barrel from the door. You will have to open the door to do this, so make sure to have someone available to help.

After you have removed the cylinder from the handle you can replace it with a brand new one. Make sure that the new cylinder has the same size as the previous one. In the event that it isn't, you could end with a handle that isn't aligned properly. This could lead to a number of problems such as leaks and drips.

A lot of door handles made of upvc have slots that allow for adjustment. These slots can be used to tighten and loosen the handle. These slots are usually found on the inside of doors, near the place where the handle joins the cylinder. Allen wrenches can be used to tighten the slots for adjustment. Once you've made the necessary adjustments, you can screw the handle back in and put it back in its place. Then, you can test the handle to make sure that it is working correctly.

If the door handle made of upvc becomes loose or floppy when it is closed, it's usually a sign that the upvc gearbox has failed or the internal spring components are breaking down. This can cause your upvc multipoint locks to fail and leave your door open to burglars. In this scenario the upvc gearbox will require replacement. The cost will range from PS145 to PS280, including labour.