How to Replace a kia car key replacement Sportage Replacement Key

For a number of Kia models, the key contains the keyless entry system that is built into the key. The key functions like the remote control and can be exchanged with a Kia dealer.

Key fobs might stop working due to a variety of reasons, including the battery being dead, worn-out buttons, signal interference or water damage. Here are some helpful tips on how to get your Kia Sportage replacement key back to working.

How to replace a smartkey or remote key?

No matter if your Kia is equipped with an intelligent key, remote key push to start key or a regular non-transponder metal key, the battery in these keys will eventually need replacement. This is especially relevant if your vehicle shows a message that states the remote or smart keys aren't powered.

Luckily, it's an easy process. To replace the battery of the key fob, remove the mechanical key from the slit in the back of the key fob. Then lift the cover. Inside the key fob there will be the small screw that holds the battery in the correct position. By using a small screwdriver loosen the screw and pull out the old battery. Insert the new battery and then close the gap on the key fob.

Test the key fob by pressing the lock/unlock buttons. If the doors unlock and lock in the same way, you're all set! You can now use Kia's hands-free lock/unlock function whenever your fingers get chilly or you need to go on errands around Brandon.

Note: Certain keys may require to be programmed (transponder chips or smart keys). This requires a particular programming machine that only the dealer or locksmith has access to. Other keys (non transponder keys made of steel) do not require programming. If you want to change the programming of your key, it is necessary to note the key code's number on the key code tag.

How to replace the battery

If the Kia key fob doesn't respond when you press the lock/unlock button, it's a sign that the battery is not fully charged. A low battery could cause other problems like the check engine light flashing on or the engine not cranking. It is quite simple to replace key fob batteries with only some tools.

Make sure to shut off your vehicle and shut the doors before you begin. Find the small metal or plastic piece on the bottom of your key fob, and jiggle it until a metal key pops out. Then, you can insert the key in the door handle of the driver to unlock your car.

To replace the battery on the key fob, you must remove the cover on the rear. Make use of a plastic pry tool to loosen the latch that holds the black negative cable. Remove the old battery and then orient the new battery to ensure that the "+" positive side is facing your face and the "negative" negative side is facing the fob's electrical contacts made of metal. Push the new CR2032 battery straight into place with care to avoid using too much force to avoid damaging or breaking the contacts on the metal.

After the new battery has been installed then turn the key fob off and then on in the ignition several times until the door locks. You can then test your Kia's key fob once more to ensure it is working correctly.

How to replace the smart key

You may have either a standard keyfob or a Smart Key depending on the model of Kia Sportage. The difference between the two is that the smart key is equipped with a small mechanical key blade that is hidden inside, while the standard key fob does not. Both types of key fobs are equipped with a battery inside them which eventually needs to be replaced. This is an easy process that takes only two minutes.

Before you get started, you will want to ensure that you're on a flat surface with sufficient lighting and that your Kia is turned off. Keep in mind that the fob contains tiny parts that could be thrown off in the event of a mishap.

The small release button is located on the lower backside. It could be a circular silver button or a rectangular slot. You can open the key fob by pressing the button.

Once you have the key fob open, you can simply remove the old battery and replace it. The new battery is the CR-2032, and it can be purchased through the internet or at a local auto parts shop. After you're done, your key fob should allow you to lock or unlock and start your vehicle, even if it isn't running.

How to replace a mechanical key

The Kia key fob is an amazing option that lets us lock and unlock our car with the press of the button. As with all devices like a key fob, the Kia can occasionally have problems. There are solutions to fix these problems and keep your key fobs running for many years.

One of the most frequent issues is a low or dead battery. This can cause your device to stop working or work intermittently. If this is the case then replace the battery with a new one.

If this doesn't fix the problem then try using a normal flat-head screwdriver to break open the fob's plastic casing. Be careful not damage any internal components, or scratch the plastic. Once the battery is removed and replaced with a new one.

Close and open the door with the mechanical key. (Every kia picanto key fob replacement fob comes with a spare mechanical key that fits into the slot). Test the key fob to confirm it's working properly. If the key fob isn't working, contact a locksmith or dealer to solve the issue. Make sure they cut you an emergency key that works for all trunk and door cylinders to avoid lockouts again.