Reasons to Change Door Lock

There are many reasons to change door lock, from upgrading your home's security to redecorating your entrance. It is also possible to change locks if your key is stuck in the lock or is difficult to turn.

Even DIY beginners can easily change their lock. To begin, gather the required materials.

Remove the old lock

Before installing a new lock, it is important to take out the old lock from the door. This is essential in the event that you suspect that someone else may have access to the home. It is also a good idea if you have recently moved into a home that was burglarized, or welcomed a new roommate. The process is simpler than you imagine and can be completed within only a few minutes.

Start by removing the screws that secure the deadbolt faceplate onto the frame of the door. You will need to take off the screws on both sides of the door in order to remove the faceplate. This will allow you to see what is behind it and give you a better idea of what to do with the rest of the steps.

After you have removed the old faceplate, you will need to remove the bolt and strike plate. Make use of a screwdriver to loosen the bolt and take it out of the hole in the door. If the bolt is rusted you may have to use a chisel to smash it. If you're using a chisel, be careful not to scratch the door frame.

Make sure that the new deadbolt, doorknob and lock fit in the holes already in the door before removing the old one. A lot of hardware stores and big box stores stock a range of locks and can assist you in choosing the right one. If the lock you purchased doesn't match your door, send it back and seek assistance.

Find small depressions or notches in the handle and around the trim while you remove the old lock. If you can locate them, slide a straightened safety pin or a flat screwdriver into them to loosen the handle and expose the screws beneath.

After you have removed the screw from the handle, you are able to begin to remove the knob. To do this, find the set screw located at the base of the knob and loosen. Then, remove the spindle.

Install the new lock

It's a good idea to change locks on doors throughout your home on a regular basis, particularly after a break-in or when you move into a new home with roommates. It's an affordable, simple and effective way to ensure that your home is secure. The majority of people can do it by themselves using a screwdriver, a screwdriver, and a few basic instructions. You may also wish to learn how to rekey your door lock to ensure that only you have the key.

You'll need to buy a new lock that has the same keyway as your existing lock. Locksmiths are usually able to replace your lock at an additional cost, but you can save money by doing it yourself. You can buy an entirely new lock from hardware stores or online. Standard deadbolts can be fitted to the majority of doors. However, you will have to measure your door to ensure that it will fit.

Most of the time your new window lock repair will include the cardboard template that will show the way it will fit on the door. The template can be used to drill the hole. It's much simpler than having to measure every time. If the template doesn't line to the hole you intend to drill, you should take it back to the hardware store to purchase another one.

When you install the new lock, remember to put it on the right side of the door. Check the latch. It should be marked with "up" or something similar. Make sure that the latch is correctly seated on the plate, and then secure it using the provided screws.

If you're replacing a window door repairs locks glass hinges knob lock, it's also important to be aware of the way it's operated. Some knob locks are right-handed. If you're not careful, you could place the knob on the wrong side of the door, which would hinder you from locking it from the inside or outside.

After you've finished checking your new lock to make sure it's working. You should be able both to lock and unlock the door using keys from the inside as well as from the outside. If you're not happy with the results you can call an expert locksmith to repair it.

Test the lock

If a lock on your door cannot be locked is a hassle and can be dangerous, it could also put your family's security at risk. It's easy to solve the majority of problems with door locks by performing some troubleshooting, and lubrication. Make sure that the key is properly cut, and that the lock assembly isn't loose or dirty. If this doesn't solve the issue, try applying lubrication to the door lock actuator using powdered graphite or a silicone-based lubricant.

Check that the doorlock switch, wiring harnesses and actuator connector all work correctly. To do this, consult the manual or wiring diagram to determine the function and color-coding of all the door lock switch wires. Use a digital meter or test light to verify that the actuator is receiving power and ground whenever the switches are activated. If you observe an electric voltage switch on each switch activation, that means the switches are working and it's likely the actuator that requires to be replaced.

If the switch seems to be working but the actuator doesn't move when you turn it, it could be a problem in the cylinder. The actuator cylinder has spring-loaded pins that keep the cylinder from turning until a key is inserted and pushes the pins upward to match the height of the key in that location. In the end, this causes the cylinder to spin and let the lock body open which allows the handle to latch.

If the door lock actuator is inoperable, you can remove the switch and wires from the actuator using small screwdrivers to unlock the locking bolt and separate the plastic cover that houses the electrical connector. After that, disconnect the door lock actuator and let it fall. You should be able to locate the two bolts of 10mm that keep the actuator in place, and remove them. After the actuator has been removed, you should be in a position to disconnect the black electrical connector and remove it along with the lock and actuator assembly.

Replace the key

If your deadbolt is locked or door knob is not functioning, you'll have to rekey it or replace it. It's not hard to do it yourself and can save some money. However, before you do this, it's a good idea to have a locksmith examine the locks and check for any problems. This will give you peace of peace of mind knowing that your home is safe and secure.

Remove the exterior faceplate of the doorknob/deadbolt. There may be screws that are holding it in place, if you need to remove them, use a screwdriver to loosen them and pull the faceplate off. Then, remove the interior faceplate using a flat-head screwdriver. After you have removed the faceplate, you can remove the screw and bolt from the lock cylinder.

A locksmith can tell you whether you need to replace or rekey the lock. They can also provide suggestions on the most secure measures for your home. They can also make the necessary modifications to your door and frame for an ideal fit. They will also offer a warranty on their work.

If you choose to rekey the lock, you'll have to first buy a new key for it. It is crucial to select a lock key that is fitted snugly. A key that is not the right size may harm the internal mechanism of a lock and stop it from working. Insert the key into the lock to test its size. If the key is completely against the plug then it's the correct size. If the pins protrude out of the top of the plug, they're too long.

There are many reasons you may want to change your door lock, including:

If you're moving into a former homeowner's house or have lost keys, rekeying the lock is an economical alternative than replacing it. It can also be more cost-effective than a complete upvc window lock repairs replacement double glazing window lock repairs locks (Keep Reading). However, there are situations in which rekeying your lock isn't feasible. For instance, if your double glazing window lock repair is damaged or repeatedly blocked, it's to be time to replace it.