How to Replace a Hyundai I10 Key Fob Battery

The Hyundai i10 is among the most elegant and stylish cars on the market. Its interior is more luxurious than rivals like the Citroen C1, Volkswagen UP and SEAT Ibiza.

Hyundai's keyfob can accomplish quite a bit for you. It can lock and unlock your car remotely. It also comes with a key that is mechanical that you can use in the event the battery in your fob goes out.

Dead Coin Battery

The key fob enables drivers to lock their cars and start them without having to insert keys into the ignition. This is accomplished through radio frequency signals which communicate with the onboard computer of the vehicle.

The battery inside the key fob is responsible for this signal and will eventually degrade and need to be replaced. Depending on your Hyundai model, you might or may not get a warning when the battery is nearing the end of its life. Keep a spare keyfob on your side to replace the battery promptly when it wears.

Once the new battery is installed the key fob will need to be reprogrammed by the car. You can do this with an OBDII or Hyundai Digital Key scanner, however, it is generally easier to do this at your Reno home. To complete this task, follow the instructions in the owner's manual or look on YouTube for "how to open and change the hyundai ix35 key replacement key fob battery." Be sure to write down the old battery number or take a photo of it before you remove it.

Once the key fob's been reprogrammed, the device should begin working again. If it doesn't, you'll need to visit a dealership to purchase a new one or call a locksmith on the move. They will have the experience and tools to fix the issue.

Water Damage

A key fob can be a very useful piece of technology. It allows you to lock your vehicle from home, lower your windows from outside and even start your vehicle. However, it's not indestructible and will eventually degrade from normal use. Fortunately, replacing a Hyundai i10 key fob's battery is simple and cost-effective.

It's not uncommon to drop your key fob in an puddle, a pool, or even a washing machine. It is possible to save it in the event that you act swiftly. A key fob that is wet is bad for electronics. It can cause corrosion, short-circuits and even failure.

First, try to remove as much water as possible. Flip the fob over and shake out any moisture that is visible. You might also be able to place it on top of the radiator or a hairdryer to speed up the process. After you've removed all the moisture you can, place the fob in a warm area in a place where it can dry out for a few days.

The next step is to remove the fob to remove the old battery. The majority of Hyundai i10 key fobs use the same type of battery that's found in many quartz watches. They're very simple to replace. After replacing the battery, you should take a photograph or note the location of the battery before closing the fob.

Contact with the battery is poor

The battery on your key fob might be drained. This is a frequent problem. The remote will display signs of trouble before it completely fails. Make sure that the clips made of metal aren't corroded, and they're tight. If you do, clean them with the proper battery cleaner and a wire brush. Make use of a button-cell battery that has the same voltage, size and specifications as the original.

This could be a sign your alternator may not be functioning properly. The alternator is the part that recharges your battery when you are driving. A malfunctioning alternator can drain the battery quickly and cause the warning light to switch on.

You can determine if your Hyundai is affected by a quick voltage test. If the battery is operating, the problem could be with the circuit board or any other component of the key fob. You can access the key fob by pressing an aluminum tab or button on either the back or front of the unit. After taking off the cover, insert a CR2032 ensure that you connect all the connections.

Reprogramming

Hyundai offers keyless entry on several of its models, making the trip around Littleton, Parker, and Castle Rock, CO easier than ever. If you have an ignition key you can open and lock your vehicle's doors and start the engine using the remote. But it's not impervious to destruction, and a broken key fob can cause issues. If your Hyundai keyfob isn't working, you may need to reset it so that it is compatible with your vehicle.

The first step is to remove the battery. Typically, the button cell battery is inside a tab made of plastic. If you are able to open the tab and replace the battery, make sure to use the same size and voltage as your old battery.

After the battery has been replaced, close the tab and replace retaining clips. Test the key fob again to ensure it functions.

If the key fob doesn't work, it might be time to contact an authorized locksmith or dealer. A dealer or locksmith can cut a new key and remote for you, and can also program the key to work with your vehicle. They usually charge a fee to do this, but it's well worth the investment if you need your Hyundai key fob to continue working. They can also help you find the best Hyundai key fob for your requirements.