How to Replace the Replacement Key Battery For the Saab 9-3

Saab owners have a distinct set of steps to take to add the second key. It requires dealer service using an electronic handheld computer called Tech-2. Then a new car key and transponder have to be purchased and then programmed to the car.

Change your keys regularly to prevent one from deteriorating faster than the next. This will also help keep your keys in top condition.

Replacement Case

The new key fobs for keys are not like the older Saab keys. They have electronics that make them difficult to copy. That has made car theft a lot more difficult than it was a few years ago. It has also made it more expensive to replace keys lost.

Every owner of a 9-3 Saab should have at minimum two working keys. It is expensive to replace a lost key because it requires replacing the CIM module, and programming the locking cylinders. Dealers usually charge between $100 and $200 for this.

There are ways to avoid these costly costs. Some parts suppliers will look up the code from an extra key (usually the same one that opens the doors and turns the ignition) and cut a brand new metal key blade for just a fraction of dealer cost. The key must, however, be identical to the original in order to function within your car.

You can also change the case yourself by following these steps. You will need an flathead screwdriver and patience. With the screwdriver you can pull apart the plastic, and then take off the emergency key. Once the case is open, take the electronics out and put them back into your new case. Make sure you insert the correct key and badge inside the case.

Replacement Battery

The replacement battery for the Saab 9-3 is a cheap part that can be replaced easily and quickly. The YouTube video of Cyclone Cyd demonstrates how you can replace the battery for the remote fob in only four steps. This tutorial can be used with any modern Saab key fob. However, the process may differ slightly.

The button is typically located near the saab 900 key logo on the back of the fob. This button is usually located near the Saab logo on the back of the fob. Next, use an screwdriver with a flat head to insert into the tiny hole in this button. This should be enough to unlock the case of the fob so that you can replace the battery.

Once you have installed the CR1632 batteries, you can restore your remote key fob. You can then program it into your car. The entire process should not take more than a half hour at the most. It's a very easy procedure that doesn't require any special equipment.

The process is a bit more complex if you lose the key, but it's possible. The dealer has to first verify the VIN of the vehicle, and then purchase a replacement TWICE module and key blade that has the correct unique code. After that, they'll have to cut the replacement key and then program it with a brand new tool for programming called MDI.

Replacement Key Fob

The key fob contains batteries that are used to lock and unlock your vehicle. The batteries last for a certain time and eventually fail. This is a common problem that affects all cars, and the good news is that you can change the batteries in many key fobs and not have to replace the entire case. Amazon sells replacement fobs that already have all the electronics installed. You can simply pop the case open and replace the batteries. You will need to remove the emergency key before you replace the batteries. To do this, insert the screwdriver of a small flat head into the slot in the middle. The case will split once you work the screwdriver all around it.

If you're ready to replace your keys, keep an extra set on hand. This will save you lots of money. If you have a spare, you can ask the dealer cut an additional key and program it to your car, which is much cheaper than replacing the whole key fob.

If you do not have a spare key one, you can add an additional key to your car, but this requires a lot of research and effort. It will cost you a few hundred dollars to purchase an additional car key. The computer in the vehicle also has to be programmed. Professionals can accomplish this but it's not a cheap option.

Replacement Ignition

The current SAAB 9-3 features a more sophisticated alarm system built on a keycode. This means that when you lose your sole working key, acquiring an additional one could be extremely expensive as the car has to have a specific computer module added and programming it also needs to be specifically designed to accept a different key. Even dealers can charge hundreds of dollars to program an entirely new key, if they are unable to complete the task.

If you've lost your only working key, a dealer will repair the computer in your car (known as the CIM or SAAB TWICE) in order to make an exchange, and they will charge a premium for it. Instead we can reprogram the EEPROM in your current car computer to prepare it for an additional key, slashing over 50% of the price you be charged at a dealership.

If you've been a long time owner of an 03-11 SAAB 9-3, then you probably are aware that the ignition key isn't the most durable. They can get extremely sticky and the buttons can be ripped off every now and then which is why you should think about getting a replacement if yours isn't working as it should. Luckily, replacing the ignition key isn't as complicated as it seems and is fairly easy to do using the right tools.