Repairs to uPVC Windows

uPVC is an excellent choice for modern homes. They are easy to maintain and durable, as well as long-lasting. In contrast to aluminium and timber, they don't get rusty or decay.

It is essential to clean and oil upvc window repairs doors and windows on a regular basis. This will save you from costly repairs and increase energy efficiency.

1. Broken Glass

If the glass in your window is broken it could cause a large deal of damage to your home, which can make it very hazardous and possibly fatal. It is essential to take the time to make sure that you're doing all you can to keep your windows in good condition.

Single-pane windows are fairly simple to replace, and they typically fit into frames of the past easily. However, if you have double-pane windows that are secured by internal beading it will be more difficult to take out the existing panes and install new ones. In this situation you'll need to locate some plastic spacers that assist the new pane to fit correctly into the frame of the window.

Wearing eye protection and thick gloves is a must for anyone who plans to remove the glass yourself. You should also lay down a dropcloth prior to you begin working on the window panes to ensure that any shards fall on the fabric and not onto the floor, where they could be trampled.

Once the glass has been removed and the glass is removed, it's a good idea to seal the gap with packaging tape or duct tape to prevent drafts and water from entering the home until a professional comes out and fix the window. It also acts as a barrier, preventing any intruders from getting access to your home. If the distance between the door and the window is substantial, you may need to consider a security screen that also has windows. This will provide the best of both.

2. Sagging

uPVC windows and doors are a low-cost, durable and energy-efficient alternative to timber windows made of sash. However, over time they are susceptible to a range of problems including sagging. A sagging window can cause problems with light, draughts, and even security. It is crucial to act as soon as you discover that your uPVC windows are sliding.

To repair a window that is sagging, you can try to reposition the hinges. First, you'll need to open the windows to get at the frame. Then, you can remove the hinges on the top and bottom with a screwdriver and adjust them counter-clockwise or clockwise. After you've repositioned the hinges, close the window and test it for fit. If you're happy with the fit, tighten the screws to ensure they stay in place.

If you are unable to reposition the hinges, you could need to replace the seal. Seals made of rubber can dry out and lose their elasticity over time, leading them to lose their tightness. It is important to replace your seal as soon as you can to keep your uPVC window watertight and draughtproof.

uPVC handles can also become loose. Most often, this is caused by screws that have come loose over time. However, it could be due to the fact that the handle mechanism has worn out. It's relatively easy to fix a loose uPVC hand. You'll first need to close the window and then perform a test fitting. The corners of the sash should be aligned with the casing joint. If it doesn't you can use a screwdriver to loosen up the handle. Then, turn the mechanism into position.

3. Water Leaks

If you awake to wet floors and mouldy walls each time it rains, it is important that you take action. The leaks of water from windows do not only lead to the degradation of your home's structure but also undermine your efforts to regulate the temperature inside your home. Most often, uPVC window leaks are caused by a lack or damage to the sealant.

This is a relatively easy fix that can be completed by any DIY expert. Depending on the severity of the issue the caulking used previously may require removal before a fresh layer is applied. It is crucial to remember that when it is about uPVC window repairs you should not be tempted to apply too much caulk in order to make the area harder to clean and could reduce your energy efficiency.

Verify that the drainage holes are free of debris inside them and that the sill pan is properly angled to allow the water to drain from the window. In more serious situations, you may have to replace the window.

Other signs of long-term water leakage include rotted sills and the appearance of black spots of mold on the walls near the window. This fungus thrives under humid conditions and can propagate quickly throughout the home.

It is also important to note that if the leakage originates from the glass of your double-glazed windows it may be more likely to be a problem with the glass seal, rather than the frame or sliding. A uPVC specialist can easily fix this issue by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

Hinges may be to blame for the reason that your upvc window repairs near me window is difficult to open or it opens with an ease. Any competent DIYer can replace hinges in just a few minutes.

Like all mechanical parts hinges are prone to wear out over time. The process of replacing a hinge on a window is essentially a simple procedure, but it is easier with someone else to help you hold the frame up.

Check that the uPVC hinges open and close in the correct direction. Look for the arrows on each hinge to determine the direction in which the window should be opened.

Faulty window hinges could be the result of incorrectly opening the window in a certain manner or because of improper installation in the factory. This can often be resolved by sending us a photo through our website and we will be pleased to offer you suggestions.

It is also crucial to lubricate the hinges regularly. This can be done by applying a light engineering oil to the hinges, we recommend using a solvent-free lubricant, such as the 3-in-one Multi-Purpose oil. Regularly lubrication will help the window operate and close more easily. It can also stop corrosion and reduce the possibility of sticking. Ideally, you should perform this every year. WD40 and other solvent based oils are not recommended because they could damage parts of your uPVC window repair.

5. Draughts

Draughts in windows made of upvc can be caused by different things. Firstly the hinges, again due to wear and tear may become displaced, which causes a gap to form where the sash joins the frame. If they are damaged beyond repair, it may be necessary to get them re-aligned. Secondly the interlock, this is located on the hinge of the window, may be misaligned. Again, it's feasible to give them a thorough clean, however in some cases it might be necessary to have these replaced.

These seals are susceptible to wear and tear or be damaged over time, allowing air to escape. This can be prevented by replacing them with high-quality weatherstripping. Another alternative is to replace the upvc window with low-emissivity glass, this will help to regulate indoor temperatures and will lessen draughts.

The last way to reduce draughts effectively is by using a Draught-exclusion device. These are usually made of fabric tubes filled with a filler that can be hung over your window repairs near me sill. They will help block out cold air and keep your home warm and cosy!

With a little regular maintenance and repairs your windows made of upvc will continue to provide a great level of insulation and security for your home. It is essential to remember that all windows will eventually wear out and it may be cheaper to replace them instead of fixing them. So, if you're experiencing issues with your Upvc windows, it is best to seek professional assistance as soon as you can.