How to Replace a Mazda Key

Mazda is known for its innovative and intuitive technology. Certain systems improve performance or safety, while others help to make driving your mazda 2 key fob replacement around East Stroudsburg, Easton, and Brodheadsville simpler.

The key fob is a great example of the latter. It allows you to lock, unlock and begin your Mazda by pressing a button. However its battery should be replaced every now and then.

Lost Keys

Keys that are lost or stolen can cause a lot of trouble. It is relatively simple to replace a Mazda Key for older models with regular keys made of metal. However, the latest models require computer chips with special programming capabilities that can only be created by a locksmith or dealer.

You will need to start by obtaining the VIN number for your vehicle. This information can be found on the dashboard of the car, on your insurance card or in the car's documentation. Note this information down to give to the locksmith or the dealership.

You'll also require a working spare key. Place the key in the slot and turn the ignition ON. Take the key out after five seconds, and then switch the ignition to OFF. Repeat the procedure with the second working key. Once both keys have been placed in the car, the new computer chip will become paired with your car.

If you have lost your keys and do not have a backup set, you'll need the car tow away to a dealer. You will then need to provide proof of ownership and pay for the replacement key. You may need to wait some time while the dealer places an order and pairs an additional key to your car. If you are able, have an expert locksmith create a new key in place of the dealer for a lower cost and less hassle.

Ignition Cylinder Repair

The ignition cylinder is a component of your Mazda that lets you start the car with the use of a key. If your car isn't turning or you can't put the key into the switch, you may need to replace the ignition cylinder.

Ignition cylinders fail more often than keys, which last for longer. There isn't a set maintenance schedule for them, however you can help them last longer by keeping your keys clear and avoid excessive shaking or jiggling of the key.

To replace the ignition cylinder, you must first remove any covers and trim pieces that might be blocking the way. Depending on the model, you might need to remove the cover of the steering wheel. It is also possible to remove the accessory switch and wiper. Then you can use a screwdriver or socket wrench to press the release tab on the cylinder. This will release the cylinder from its switch and allow it to slide out.

Once the cylinder is out, install the new one by connecting it to the wires, securing two screws on top and then replacing the switch cover. Reconnect the battery, and test the key insertion/removal function of the new cylinder. Connect the battery, and then repeat the process three to five times. Then, try to start your vehicle to verify that everything is working correctly.

Remote Control Replacement

If your Mazda key remote is not working, you will require the help of an expert. This is not as common as a problem with the ignition cylinder, but it can still leave you in a bind. Locksmiths are in a position to repair the car key remote and will also handle all the programming that goes along with it.

The bare minimum that you'll need to supply to a locksmith in order for them to perform this service is the year and type of your Mazda vehicle. This will allow them to collect the proper supplies and know if any additional programming of keys is required for your Mazda model.

If your key fob won't turn on, it may just have a dead battery. In this instance the best thing you can try is to reset your receiver. This can often bring back functionality. If this doesn't work, you must replace the batteries. To do this you will need to remove the key and then use a flathead screwdriver wrapped in tape to push the case open on one side. Once you've done this, insert the keyfob with a battery. Make sure that it's a suitable battery and then close the case. The Mazda's RF unit will need to be reprogrammed to recognize the key.

Transponder Chip Replacement

If you have a mazda 6 key (click here to investigate) key fob or a smart key, chances are that your car has a transponder in it. This tiny piece of technology, which functions as an micro-motherboard, transmits an immobilizer signal in your car when placed in the ignition.

These types of keys are extremely useful in terms security, because they stop other people from starting your car, by ensuring that the sole person who can actually start your vehicle is you. You must be careful not to lose or take your key.

A professional locksmith can replace transponder chip. To accomplish this, you'll need to remove the cover on your key fob. It's usually an extremely thin piece of plastic that can be removed with the screwdriver. Then, you will need to remove the chip. It should look like a tiny black square or see-through tube. Once you've completed this, simply put the chip on a piece tape and then attach it to the ignition lock.

A professional locksmith will be able to do this in a flash, and will assist you in getting back on the road quickly. Call a mobile locksmith if there are any issues with your Mazda key.