How to Replace a Kia Sportage Replacement Key

For a number of Kia models keys, the key has an integrated keyless entry system. The key is usually akin to an electronic remote and is able to be replaced with a fresh one from a Kia dealer or a locksmith.

Key fobs can stop working due to various reasons, such as the battery of the coin is dead worn buttons, water damage, signal interference and a faulty receiver module. Here are some suggestions on how you can get your Kia Sportage replacement key back to working.

How to replace the remote key or smart key

It doesn't matter if your Kia comes with an intelligent key, remote key, push-to-start keys, or a regular non-transponder metal key the battery in these keys will eventually require replacing. This is especially relevant if your car displays a message telling that the remote or smart key is not powered by the battery.

This is a relatively easy process. To replace the keyfob battery take out your mechanical key from the slit at the back of the fob. Then, you need to pry the cover off. Inside the key fob there will be an incredibly small screw that holds the battery in the correct position. Remove the old battery by unwinding the screw using the help of a small screwdriver. Then insert the new one and close the slit on the key fob.

When the key fob is equipped with new batteries, test it by pressing the lock and unlock buttons. If the doors lock and unlock according to your expectations, then you're in good shape! You can now make use of your Kia's hands-free lock/unlock feature when your fingers start to get cold or you need to make errands in Brandon.

Note: Certain keys may require to be programmed (transponder chips or smart keys). This requires a special programming machine that only the dealer or automotive locksmith can access. Other keys (non transponder keys made of metal) don't require programming. If your key needs to be reprogrammed, then you must know the key code number written on the tag that identifies the key and save it in a secure location.

How do I replace a battery

If your Kia key fob isn't responding to pressing the lock or unlock button on the fob, it is a signal that the battery should be replaced. A low battery may also cause other problems like the check engine light flashing on or the engine not cranking. Fortunately, replacing the key fob battery is a relatively simple DIY task that requires only the most basic tools.

Make sure that you shut off your vehicle and close all doors before you begin. Find the small, metal or plastic piece that is located at the bottom of the key fob. Press it until the key comes out. You can then insert the key into the handle on the door of your driver to unlock your car.

To replace the battery in the key fob, remove the rear cover. Use a pry tool to loosen the latch that holds the black negative cable. Remove the old battery and align the new one to ensure that the "+" positive side faces you, and the "-" negative side is facing the fob's metal electrical contacts. Avoid using excessive force when pushing the new CR2032 into place to avoid damage or bending the metal contacts.

After you have installed the new battery and turning the key fob on and off in the ignition until the door locks cycle. Then, you can test your kia ceed key fob replacement key fob and see whether it's functioning properly again.

How do I replace a smart key

You can have the standard keyfob or Smart Key depending on the model of Kia Sportage. The smart key comes with an embedded mechanical key blade, unlike the standard key fob, which does not. Both kinds of key fobs come with an internal battery which eventually needs to be replaced. It's quite simple and takes only two minutes.

Make sure to shut off your Kia and be on a level and well-lit surface prior to you begin. Also, remember that there are tiny components inside the fob which could fall out if not careful.

The release button for the small size is located on the lower backside. This will be either a circular or rectangular slot. You can open the key fob by pressing the button.

Once you have the key fob open then you can take off the old battery and replace it. The new battery should be a CR-2032, and can be bought online or from your local auto parts store. After installation it should be possible to lock and unlock your car using your key fob even if your engine isn't running!

How do you replace a broken mechanical key

The Kia keyfob can be a fantastic convenience that allows us to lock or unlock our car by simply pressing a button. As with all devices that is used, the Kia key fob may have issues. There are ways to resolve these issues and keep our key fobs in good condition for the long run.

One of the most frequently encountered problems is a low or dead battery. This could cause your device to stop working or operate intermittently. If this is the case then replace the battery with a new one.

If this isn't enough to solve the issue, you can use the flathead screwdriver that is standard to wedge the fob's plastic casing open. Be careful not to harm any internal components or scratch the plastic. When the battery is open, carefully take off the battery that was removed and replace it with a new one.

Close and open the door with the mechanical key. (Every kia fob comes with a spare mechanical key that fits into the slot). Test the key fob to verify that it's working properly. If the key fob isn't working, call an expert locksmith or dealer to help solve the problem. To avoid locking outs in the future, make sure you get an emergency key that can be able to work with all door and trunk cylinders.