How to Replace a Kia Sportage Replacement Key

For many Kia models, the key contains an integrated keyless entry system. The key can be compared to an electronic remote and is able to be replaced with a new one from an Kia dealer or locksmith.

Key fobs are prone to malfunction due to a variety of reasons, including a dead coin battery, worn buttons, signal interference, water damage and a damaged receiver module. Here are some tips to assist you in getting your Kia sportage replacement key to work for good.

How to replace a remote key or smartkey

No matter if your kia replacement key is equipped with an intelligent key, remote key push to start key, or regular metal non-transponder key the battery in these keys will eventually require replacing. This is particularly relevant if your vehicle displays a message that indicates that the remote or smart key is not powered by the battery.

It's an easy procedure. To replace the battery of the keyfob, remove your mechanical key from the slit that is located at the back of the fob. Then, you need to pry the cover off. A small screw will be found inside the key fob, which holds the battery in its place. With a small screwdriver, loosen the screw and remove the battery that was in place. Install the new battery and then close the opening on the key fob.

Once the key fob has an updated battery Test it by pressing the locks and unlock buttons. If the doors lock and unlock exactly as you expect, then you're good to go! You can now take advantage of the hands-free lock/unlock feature on your kia sportage key fob replacement whenever your fingers get chilly or you need to go on errands around Brandon.

Note: Some key fobs may need to be programmed (transponder chips or smart keys). This requires a special programming machine that only the dealer or locksmith can access. Other keys (non-transponder metal keys) do not require programming. If your keys need to be reprogrammed, then you will need to be aware of the key code printed on the tag that identifies the key and record the number in a secure place.

How do you replace a battery?

If your Kia key fob isn't responding to pressing the lock or unlock button on the fob, it is a sign that the battery should be replaced. A weak battery can cause other issues such as the check engine light coming on or a delay in cranking the engine. Fortunately, replacing the battery on the key fob is a fairly simple DIY project that requires only the most basic tools.

Make sure you turn off your vehicle and close all doors before you begin. Find the small metal or plastic piece at the bottom of your key fob, and gently jiggle it until the metal key slips out. The key can be put into the driver door handle to unlock your car.

To replace the key fob's battery, take off the cover from the back and use a plier bar tool to loosen the latch that holds the black negative battery cable. Remove the old battery and then orient the new battery so that the "+" positive side is facing your face and the "negative" negative side is facing towards the fob's electronic contacts. Push the new CR2032 battery straight into position with care to avoid using too much force to avoid damaging or bending the contacts on the metal.

Once the new battery has been installed after which you turn the key fob off and then on in the ignition several times until the door locks. Then, test your Kia key fob to check whether it's functioning properly again.

How to replace the smart key?

Depending on the model of the Kia Sportage, you may have an ordinary key fob or a smart key. The difference between the two is that the smart key has the small blade of a key tucked inside it, while the standard fob does not. Both types of key fobs are equipped with batteries which eventually needs to be replaced. Luckily, this is a fairly simple process that takes only two minutes.

Before you begin it is essential to ensure that you are on a flat surface with adequate lighting and that the Kia is off. Also, remember that there are tiny pieces inside the fob that could fall out if you are not vigilant.

The release button for the small size is located on the lower backside. This will either be a circular silver button or a rectangular slot. Once you press this, the mechanical key blade will come out and you can then open the key fob.

Once you have the key fob opened then you can take out the old battery and replace it. The new battery should be a CR-2032 and can be purchased online or at your local auto parts store. After installation you should be able to lock, unlock and start your car with your key fob, even if the engine isn't running!

How do you replace a broken mechanical key

The Kia keyfob can be a fantastic convenience, allowing us to lock or unlock our car simply by pressing a button. As with all devices it is possible that the Kia key fob may have issues. There are ways to solve these issues and keep your key fobs in good working order for an extended period of time.

A dead or weak battery is among the most common problems. The battery could cause the device to stop working or work intermittently. If this is the problem then replace the battery with an entirely new battery.

If this isn't enough to resolve the issue Try using a standard flat-head screwdriver to break open the casing of the fob's plastic. Be careful not to damage any internal components or scratch the plastic. When the battery is open, carefully take off the battery that was removed and replace it with a new one.

Close and open the door with the mechanical key. (Every Kia fob comes with an emergency mechanical key that fits into the slot). Test the key fob and verify that it's working correctly. If the device isn't working, contact a locksmith or dealer to help resolve the problem. Make sure they cut you an emergency key that works for all trunk and door cylinders to prevent lockouts in the future.