How to Replace the Replacement Key Battery For the Saab 9-3

Saab owners have to follow a series of special steps to install a second ignition key. This requires the use of a handheld computer called Tech-2 that is operated by the dealer. Then the transponder must be replaced and a key are required to be purchased.

It is recommended to rotate your keys so that one does not get worn out more quickly than the other. This will keep your keys in perfect condition.

Replacement Case

In contrast to the traditional Saab keys of old keys, the modern key fobs have electronics inside which makes it difficult to duplicate. That has made car theft considerably more difficult than it was a few years ago. However, it has made the replacement of lost keys a more expensive undertaking.

Saab Milton keynes 9-3 owners must have two keys working. It is expensive to replace a lost or damaged key since it requires replacing the CIM module, as well as reconfiguring the locking cylinders. Dealers charge between $100-$200 for this.

There are ways to cut down on these high costs. Some parts retailers will look up the code from an extra key (usually the same one that opens the doors and turns off the ignition) and cut a new key blade out of metal for just a fraction of dealer cost. The key, however, must be identical to the original to work correctly in your car.

Follow these steps to replace the case. You'll need an open-faced screwdriver and patience. With the screwdriver slowly break the plastic and separate the emergency keys from the case. Once you have the case open, remove the electronics and put them in the new case. Be sure to put the correct key and badge back in the case too.

Replacement Battery

The replacement battery for the Saab 9-3 is an affordable component that can be replaced easily and quickly. This DIY video from YouTube Cyclone Cyd, a user on YouTube, explains how to replace the battery in the remote key fob in just four steps. This tutorial is compatible with any modern Saab key fob. However, the process may differ slightly.

This button is usually located close to the Saab logo on the back of the fob. It is usually located close to the Saab logo on the back of the fob. Then use a flathead screwdriver to insert into the tiny hole in this button. This will be enough to allow you to open the fob's case to allow you to replace the battery.

Once the new CR1632 battery is installed, you can reassemble the remote key fob and program it to your car. The whole process should take more than an hour at most. This is a simple procedure that doesn't require special tools.

If you lose your key, the procedure will be somewhat more complex however, it can be done. The dealer will first need to read the VIN of the vehicle and then order an alternative TWICE module, as well as a key blade that is matched to the unique code. After that, they'll have to cut the replacement key and then program it with the latest software tool known as MDI.

Replacement Key Fob

The key fob has a battery that is used to lock and unlock your vehicle. The batteries have a lifespan, and they will eventually go out of service. It is a common problem for all vehicles. The good news is that you can replace the battery on most key fobs without having to replace the entire case. You can purchase replacement fobs from Amazon that come with all the electronics already in place, so you'll just pop open the case and replace the batteries that were in the case. You'll need to take out the emergency key before you can replace the batteries. To do this, place a small screwdriver that is flat into the slot in the middle. The case will split when you rotate the screwdriver around it.

If you're planning to replace your keys, keep a spare available. This will save you a significant amount of money. If you have an additional key, request the dealer to cut the key and program it for saab milton keynes your vehicle. This is much less expensive than purchasing a new fob.

If you do not have a spare key one, you can add an additional key to your car, however it requires a lot of research and effort. It costs around a hundred bucks to add an additional car key. The computer in the car must also be programmed. This can be accomplished by a professional, but it's a costly choice for most owners.

Replacement Ignition

As opposed to the earlier Saab automobiles, the new SAAB 9-3 models use a much more sophisticated alarm system that is based on a coded key. This means that should you lose only one working key, adding another key can be extremely costly since the car needs to have a specific computer module installed and it also must be specially programmed to accept an extra key. Dealers can charge hundreds of dollars to program an additional key when they are not able to complete the task.

Dealers will charge you a premium to replace your car's computer (also known as the CIM or SAAB twice) in the event that you lose the only working key. We can reprogram the current EEPROM of your car's computer to be prepared for a new key. This will save you more than 50% off what you would pay at an auto dealer.

If you've been an owner of a 03-11 saab spare key 9-3, then you likely know that the ignition key isn't really all that robust. If the ignition key you have isn't functioning properly, it is time to look into replacing it. They can become sticky and the buttons have been known to fall off. It's not as difficult as you think to replace the ignition key. With the appropriate tools, it could be accomplished in a matter of minutes.