Cat flaps allow your pet to go in and out whenever they want without needing to let them in or out. They also prevent your cat from urinating in the house.

Fitting a cat flap in a upvc door panel with cat flap door panel is a lot easier than a glass door, however it will require some expertise and the appropriate tools.

Measure the Door

The installation of a cat flap in the front door is difficult, but so long as the cat flap is of the correct one and you follow the guidelines you can make it less difficult. We will demonstrate how to draw the shape and then use the jigsaw to cut the door's area. Then, we'll finish the job by attaching the cat flap installation flap. This will ensure the flap stays in position and also protects the doors from the damage caused by rain and wind.

To determine the size of the cat flap you need, measure the width of your pet. This will enable you to select a flap that is large enough for your pet to walk into the home and exit without having to open the door each time.

Once you have the measurements, you can mark out the area on the door where the template should be positioned, usually this is done with an X, but some kits include drawings that show where to drill. If yours does, then you can stick it to the door and draw a line around it. If your door has moulding or a sill at the bottom, be sure you leave plenty of space between your cat and the moulding or sill.

Set a square to make sure you are cutting correctly and ensure that the hole is a perfect rectangle shape. Once you are happy with this, you are able to begin to remove the rest of the door material. If you have an already-cut square, make use of it to verify that you are cutting correctly and to ensure that the hole is a proper rectangle. Once you are satisfied with this you can begin to remove the rest of the door material.

Draw a Line

The cat flap allows you to let your pet in and outside without having to worry about unwanted visitors or unwelcome gifts. It also reduces drafts and helps keep the temperature inside your home steady. However, installing the cat flap to your door might seem like an overwhelming task for those who haven't done it before. This can lead many people to seek out a professional joiner or carpenter to complete the task. This is an option but you can do it yourself if the tools are appropriate and the directions are followed.

This is much easier to accomplish on wooden doors, but it is still possible with uPVC. However, you must be careful not to scratch the doors since this could make it impossible to claim your warranty. First, you need to examine the door's measurements to ensure it will accommodate the new cat-flap. If you have a standard uPVC panel it should be a breeze. However, if your door is made of composite or another kind of door, you may have to be more cautious.

Next, you will need to determine the height of your belly for your cat. This is the distance from the floor to the bottom of the cat's stomach and you'll need find a place near the door where this measurement is within the range that your cat can comfortably pass through. Once you have this information, you will be required to mark the area with pencil and a spirit level to ensure that the hole you will make will be a good fit for your cat.

After you have marked the area, it's now time to cut the hole. It is important to be patient and use a jigsaw ensure that the cuts are clean and smooth not uneven and rough. This could cause damage to your door. Wear safety glasses and a dust mask while using a jigsaw. Inhaling sawdust can be harmful for your health. After you've cut the hole, you will need sandpaper to smooth the edges so that the cat flap is easily fitted into place.

Make a hole

It can be difficult to put an animal flap on the door panel or double glazing unit. You might be tempted to tackle the task yourself, but unless you have a lot of experience with DIY, it's likely to be best to have a professional to do the job for you. A mistake could not only be unsightly but also pose an security risk. It could let cold air in when the cat is outdoors and hot air out when it is inside.

The hole's location should be marked on the door using the help of a pencil and a spirit level. This will ensure that it is positioned correctly and is flush with the door's other parts. Make sure to have sandpaper to smooth out any rough edges.

Once the line has been drawn, you can cut the hole with a jigsaw. Be sure to wear any safety equipment for working with a power tool. If you are worried about the sound produced by a jigsaw you can buy a cordless version which is quieter and simpler to use.

It is best to only remove the material needed to create the cat flap. It is necessary to leave a bit of material to cover the wall of the flap. However cutting away too much could cause issues or even damage to the door frame.

A door made of upvc may include a metal frame, or a panel inside that could interfere with the microchip cat flap, and if this is the case, you'll need to cut an over-sized hole to ensure that the metal doesn't touch the the cat flap. If this is the case, it is important to fill in the oversize gap and seal it with water.

If you are fitting an animal flap to an upvc door or a double glazed windows with a metal frame then you will need to speak to a professional who will supply you with a new pane of glass with the hole for the cat flap premade in it. It will be much cheaper to do this instead of trying to install a cat flap into an existing glass pane that was not designed specifically for this purpose.

Fit the Flap

Cat flaps give your pet the freedom to go and come whenever they like and allow them to be comfortable in the house when they want to. If you have a uPVC front door, cat flaps it may be hard to install a cat flap. This is particularly true in the event that you don't own a glass panel that is cut. Luckily, if you're happy to purchase and install a new half-glazed uPVC panel, then it's possible to fit an animal flap onto the doors. It's not a simple matter of drilling an opening in the door. You'll also have to perform a few steps to ensure it's secure.

A composite, uPVC, or GRP door panel typically comprises an extremely thin plastic outer skin joined to a soft polystyrene core that is insulating. It is important to be careful when cutting the material. This type of door usually includes a template which you can use as a reference to cut the hole in your door.

Once you've marked the opening in your front back door with cat flap fitted, it's time to put in the cat flap. You can pick from a variety of designs, from simple push-button models to ones that are microchip-activated and allow only your pet to enter. However, no matter what kind of cat flap you select, it's crucial to ensure that your cat can use the flap and not get trapped outside in bad weather.

A circular fitting is better than a square one, as circles can be cut more securely into the glass. This is because square holes make glass more vulnerable to cracking if drills are used on it. It's also a much safer option as you're not putting yourself at risk by drilling into toughened glass that may break and cause injury to your pet or family members. This is particularly important if you have child or elderly person in your home who could be hurt by shards of glass.