Reasons Why Your Nissan Qashqai Key Fob Won't Work

The Qashqai's large dimensions give it an SUV feel. Its ride on 19-inch alloy wheels on Ti and STL models may also be a bit firm. The front tyres of the Qashqai can lose grip on rough surfaces, and its CVT may occasionally exhibit wrist-flexing torque steer.

This is typically caused by the battery being dead, which can be replaced in a matter of minutes. Make sure that the replacement battery is of the same voltage, size and specifications.

Water Damage

One of the most frequent reasons why a Nissan key fob will give the "key ID incorrect" message is due to water damage. The key fob is fitted with rubber seals which protect the chip inside. However, prolonged exposure to moisture can cause it not to function properly. It's typical to observe this if your keyfob was dropped into the ocean or in a pool. However, it can occur when it's wet due to rain or soapy hands.

If your key fob has been exposed to water for an extended period of time, it could need to be cleaned with isopropyl alcohol, or electronic cleaner. Or, it could require taking to a specialist for repair or replacement.

If your key fob requires to be replaced, it is an easy procedure. Make sure you have the correct multipack (CR2032, 3V). Unlock the front and rear cases with the flat-head screwdriver. Remove the metal clips, then remove the battery that was in place and replace it. After reassembling the fob, put the mechanical key back into position and ensure that it is working correctly. If not then you'll have to take it to a Nissan dealer or a professional auto locksmith to repair the chip in the key. The chip is not usually damaged near by water and therefore shouldn't be too expensive.

Dead Coin Battery

The coin battery is another common reason for why your Nissan Qashqai remote key fob may not work. The batteries typically last for 3-5 years, but they may fail with time, particularly when the fob is frequently dropped. You can replace the battery with a fresh one, but make sure that it's the same voltage and size as the original. If you are using a different battery it may cause the key to have an untrue key ID, which will prevent it from pairing with your vehicle.

The best way to replace the battery of a coin on a Nissan Qashqai key fob is by opening the fob with a small flat head screwdriver. In the screwdriver, push it into an angled notch on the bottom of the fob and twist gently to separate the two parts of the key fob. Then, take out the old CR2025 button cell battery and replace it with another one after confirming its location on the fob.

Examine the terminals for dirt or water damage prior to installing the new battery. If there is, clean the terminals using a small amount of isopropyl alcohol. Make sure that the pole cables are connected correctly. They should be connected both the positive and negative poles of your battery.

Fault Diagnosis

If your Nissan Qashqai key fob stops working after exposure to pure rain or tap water it could be a sign of an internal chip problem. You'll require a new keyfob if you can't fix the problem by replacing the battery. If the key fob has stopped working after dropping it, it is likely that the chip inside was damaged. If you clean the chip using isopropyl alcohol and paper towel and then insert it into the key fob, you'll generally get it working.

Key ID Incorrect is a common error that can be seen on the dashboard of your vehicle. The vehicle is not able to recognize the key fob, and consequently, won't allow the vehicle to start. The problem can be caused by many things, including water damage, undetectable malfunctions in the key fob's circuitry or RFID interference.

If the 12 volt battery in your key fob dead or not providing enough electric power, it will stop working. This will affect the remote keyless system as well as central locking in your Nissan Qashqai, as well as stopping you from starting the engine using the key fob (if equipped with Intelligent Key). If you're unable to unlock or lock the door by hand you must check the batteries in your key fob to be sure they are in good shape. Try reconnecting the battery in order to reset your transmitter.

Reprogramming

If the key fob was not submerged into saltwater the device should be able to be restored to its original state with a simple wash of clean water. You can also clean the electronic component using isopropyl or electronic cleaner. If none of these methods work, you may need to replace the key fob.

If your Nissan Intelligent Key still does not work, there might be a problem connecting between it and the vehicle. Start by turning the ignition switch without initiating the vehicle. Continue to do this until the hazard light blinks twice. After that, turn the car off and take out the keys.

Open the fob compartment in your vehicle's fob compartment. It's usually found on a door jamb or the handle for the driver's door. Find the small "program" button and press it. You should hear a chime sound after the process is completed.

It's time to put your Intelligent Key to the test. Make sure you press all the buttons on the key while standing at a distance from the vehicle. If the lights flash or the horn sounds, then the key is connected to the nissan micra key replacement. You can also test it close to the Nissan.