Repairs to uPVC Windows

uPVC is a great choice for modern homes. They are durable, long-lasting and easy to maintain. Unlike timber and aluminium, they don't get rusty or decay.

It is important to clean and oil UPVC windows and doors regularly. This will prevent unnecessary repair costs and increase energy efficiency.

1. Broken Glass

The broken glass in your windows can cause serious damage to your home and may even be fatal. It is important to take the time to ensure that you are doing everything you can to ensure that your windows are in good shape.

Single-pane windows are relatively easy to replace and generally fit into frames of the past easily. However when windows with double panes are secured by internal beading, it will be more difficult to get rid of the existing panes and install new ones. In this instance, it is necessary to buy plastic spacers to help the new pane fit into the window frame.

Wearing eye protection and thick gloves is essential when you are planning to remove the glass by yourself. You should also lay down a drop cloth before you begin working on the window panes to ensure that any shards of glass fall onto the fabric and not on the floor, where they could be trampled under.

After the glass has been removed from the window, it's best to seal the gap with clear packaging tape or duct tape to stop water and drafts from getting into the property until a professional comes out and fix the window. This will also act as a barrier, preventing any intruders from getting access to your home. If the gap between the window and the door is large, you might need to consider security screens that has windows. This will give you the best of both.

2. Sagging

uPVC is durable, energy-efficient and affordable alternative to timber sash window. Over time, they can be affected by a variety of issues that include sliding. A window that isn't properly aligned can cause problems with light, draughts, and even security. If you find that your uPVC window is beginning to sag it's crucial to act fast to prevent the problem from getting worse.

To fix a sagging window you can try to reposition the hinges. To do this, you'll have to open the window so that you can get to the frame. With a screwdriver, you can remove the top and bottom hinges and adjust them by turning them clockwise or counter-clockwise. Close your window to check the fit after you've repositioned your hinges. If you are happy with the fit of the window, tighten the screws to keep them in the right position.

If you cannot reposition the hinges, you might have to replace the seal. Seals made of rubber can dry out and lose their elasticity over time, leading them to loosen. If this happens, it's crucial to replace the seal as fast as possible so that your uPVC windows are waterproof and safe from drafts.

uPVC handles could also loosen. This is often caused by screws that have become undone over time, but it can be due to the mechanism of the handle wears out. It's relatively easy to repair a loose uPVC handle. You'll first need to close the window and then perform an experiment fitting. The corners of the sash need to align with the casing joint. If it doesn't, you can use the screwdriver to loosen the handle. Then turn the mechanism back into place.

3. Water Leaks

It is important to act if you get up each morning to discover mouldy walls and floors that are wet. The leaks of water through windows could cause structural damage to your home and also hinder your ability to control the temperature in your home. The most common cause for leaking uPVC windows is that the sealant surrounding the frame is damaged or missing.

This is a simple fix that can be done by anyone who is a DIYer with the skills. Depending on how severe the issue is, the old caulking may need to be removed. When it comes to uPVC repair, you must be careful not to over-caulk. This will make your window more difficult to clean and lower its energy efficiency.

Verify that the drainage holes have no debris in them and that the sill pan is angled correctly to drain away from the window. In more serious cases you may need to think about replacing the window.

Mold spots and rotten sills are also signs of water leakage. This fungus thrives in damp conditions and can spread quickly throughout the house.

It is also important to note that if the leak is coming from between the glass of your double-glazed windows, it is more likely to be an issue with the glass seal, rather than the frame or sliding. A upvc door repairs near me (read the article) specialist can fix this issue by replacing the glass seal. This will ensure the complete insulation of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or slack and open with a breeze, it may be hinges at the fault. These are easily repaired by any skilled DIYer and can be done within a few minutes.

Like any mechanical component hinges will be damaged over time. It is essentially a very simple procedure, but it is easier with someone else to assist in holding the frame in place.

It is also worth checking that the uPVC hinges are opening and closed in the correct direction. Look for the arrows that are on each hinge to determine the direction in which the window should be opened.

The problem can be caused either by opening the window repair incorrectly or by a poor installation in the factory. Sending us a photo via our website is often enough to resolve the problem. We are more than happy to offer advice.

It is also crucial to lubricate the hinges regularly. Applying a light engineering lubricant to the hinges is a great method of doing this. We suggest using a lubricant that does not contain solvents, such as 3-in-1 Multi-Purpose oil. Regularly lubrication makes the window easier to open and close. It can also stop corrosion and reduce the possibility of sticking. This is recommended to be done at least every year. WD40 and other solvent based fluids are not recommended since they will damage parts of your uPVC window.

5. Draughts

Draughts in Upvc windows can be caused by a few various factors. The hinges can also be misaligned due to wear, which can cause a gap between the frame and sash. These can be easily repaired by giving them good clean, but when they're beyond repair, it could be necessary to have them aligned or replaced. The interlock may also become misaligned. This happens on the hinge's side and may need to be cleaned. In certain instances it is possible to replace these.

The second most frequent reason for draughts are the window seals. They are susceptible to being worn out or damaged over time and will allow air to escape through the gaps. Installing high-quality weatherstripping can help prevent draughts. Another alternative is to replace the upvc window with low-emissivity glass. this will help in regulating indoor temperatures and will reduce draughts.

Another, and most effective ways to reduce draughts is by using a draught excluder, these are usually fabric tubes that are filled with some type of filler. They can be placed on the top of your windowsill. They will help stop cold air from entering and keep your home warm and cosy!

The windows made of upvc can keep providing excellent insulation and security in your home with a little regular maintenance and repairs. It is crucial to recognise that all windows have a life span and they may reach a point where it is more economical to replace them than repair them. If you encounter any issues with your window made of upvc, it's best to consult an expert as soon as possible.