UPVC Window Repairs

uPVC windows are energy efficient and can aid in reducing heating costs. As they get older, however, issues can occur that need to be fixed. This could include damaged hinges, handles or locks.

Wooden window replacement repairs can be fairly simple for DIY enthusiasts to complete themselves. It can also be much cheaper than a new replacement window.

Cracks

Cracks and tears in uPVC windows could be a serious issue. If windows are not properly repaired, they can result in water intrusion and weaker barriers to cold weather, and can cause structural damage. It is crucial to find an experienced local repair or builder that specializes in repairing uPVC frames and has the expertise, experience, and tools required to deliver the most effective results. This will ensure that your fracture is repaired quickly before it gets worse and you don't need to replace your window unit or glass.

Small cracks in glass can be fixed with a range of home-based solutions. Masking tape and superglue are two of the most commonly used products used to keep glass that has cracked in place for a brief time. For cracks that are more extensive the tape may have to extend past the crack on both sides to get the optimal results.

Alternatively, two-part epoxy can be used to repair broken or cracked glass. The majority of hardware stores sell this product for about $10. Make sure that your workspace is ready before mixing the epoxy. Also, make sure you have all the equipment necessary for the job.

If you notice that your lower or upper sash isn't lifting it is most likely due to the cords attached to the sashweights are damaged. It's an easy fix that can be accomplished with the help of the ladder and a flathead screwdriver. A rotted dripcap can also be replaced at home. Most home centers carry drip caps that are rot-free and can be easily nailed or caulked in place. Lastly, if you have a double or triple-paned window, be certain to ensure that one of the panes isn't broken. The reason is because the gases in the space between the windows are responsible for enhancing the efficiency of the window. This should not escape.

Water Leaks

If your uPVC windows leak, it could damage the interior of your house and result in costly repairs. Water leaks can also affect the structure of your house and cause mold growth. It is important to fix any problems caused by leaking windows right away to minimize damage.

A damaged sealant around window frames is a common cause of leaks. Using silicone caulking can help restore the condition of the seal back to normal and prevent water leakage. It's also important to check for cracks and gaps around the frame as well in the stone or brick walls that surround your windows.

Another reason that can cause leaks in windows is a blocked drainage hole or faulty flashing. It's crucial to make sure the drainage holes are free and unclogged, especially after a heavy rainstorm. You should also examine the windows' flashing to ensure that it is properly sealed.

Lastly, it's important to make sure that your drip cap isn't damaged or damaged. A rotted drip cap or one that's not there will allow water from above to get into your window and cause structural damage. Replacing the drip cap isn't difficult and generally a simple process of purchasing an entirely new one and putting it in place.

It's an excellent idea to have your windows checked for water-tightness by a professional. They can employ a tool to determine the water-tightness of your windows, and ensure that they comply with industry standards. If your windows fail the test, they will require replacement. It's a costly fix, but is worth it to ensure the safety and security of your family.

Sagging

If your windows do not close properly, it can lead to a number issues, such as condensation, drafts and a rise in your energy bills. It can be a sign that the windows were not properly fitted when they were installed or that the sealant is no longer working. There are a few options you can try to resolve the problem.

The first step is to prepare your workspace in a space with plenty of natural light to help repair your window correctly. Begin by laying newspaper or an old blanket on the floor to shield it from any drips or upvc window Repairs splinters that might be coming from the window during your work.

You will also want to use a white cloth that has been soaked in a solution of water and detergent. This will stop any stains of color from appearing on your windows. If you're ready to start working on your uPVC windows, start by marking the location where the hinge channel needs to be located. Then remove the channel from the frame and fill in the screw holes with epoxy (for uPVC windows) or wood filler (if frames are made of wood). Make sure you scrape the hole you have filled before it sets.

Once the holes are filled you can reinstall the hinge channel. Make sure that it is centered on the window jamb, and that you drill the new holes approximately a quarter inch from the original locations.

Then, take a measurement of the spindle protruding from the underside of your handle. You can request an replacement or take it to a shop selling hardware for a replacement. Then, remove the setscrew off the operator shaft. Flatten it to allow the set screw to be locked onto the shaft. Then, your uPVC windows should shut without a hitch.

Broken Hinges

If your uPVC window hinges are damaged or are not functioning correctly, you will find it difficult to open or close the window. This can cause problems with security and prevent your home from being warm or cool. You can easily get a new hinge for your uPVC window. It's crucial to choose the right type for your windows.

The hinges have to be identical in size to fit inside the frame of the window. The most commonly used hinges for uPVC windows are standard 18mm or UPVC 15mm hinges for windows. However, there are special kinds of window hinges that are suitable for other types of frames such as wooden frames. Finding the right window hinge for your windows can help you avoid the common problems that many homeowners encounter with their windows, for example, not closing properly.

The hinges of your window may be loose or stiff for several reasons. One common cause is that the hinges are not properly securing. To test this, take an electric screwdriver to locate the friction screw at the end of the hinge. Loosen it. You can then adjust it by turning it in either direction.

Contact Preston Glass Fix if your UPVC window's hinges don't work correctly. We can offer an immediate solution. Our experts will assess the condition of your hinges for your windows and provide you with the best solution for you. We can replace window hinges or retension them, or even install new lock mechanisms to ensure your UPVC Windows are secure and safe.

Faulty locks

UPVC window mechanisms and locks are an important element of home security. They make it extremely difficult to open windows without breaking into the house. It can be a hassle when a lock fails but you don't need to replace the entire window.

It's often an issue that is minor and could have been easily avoided with regular maintenance. This is the reason we recommend that you have your uPVC windows serviced regularly with our yearly maintenance package to help reduce the likelihood of having problems.

Modern uPVC windows come with espagnolette locks. They work by pushing the nose end of the handle on the block with a wedge, and then turning it to close the lock. They are very effective in keeping the window closed, however over time, they could begin to fail if they're not properly maintained. We suggest using WD-40 for lubrication a couple of times per year.

If you notice that your uPVC windows aren't opening or close as smoothly as they used to or when the lock isn't working properly it is likely that there is an issue with the locking gearbox within the window frame. This can be difficult to access as it requires the removal of the seals that surround the window frame and taking off the handle.

A locksmith who specializes in UPVC repairs will have the expertise to quickly identify the issue and then be able replace the damaged gearbox for locking with a exact replacement. This simple and quick fix can save you hundreds by avoiding having to purchase new windows.