Fiat 500 Replacement Key Fob

It might be time to replace the battery if your 500 remote key fob is not working. If you replace the battery but it doesn't work it could be a problem elsewhere.

At United Locksmith, we specialize in making new keys for classic cars. We have the tools and parts needed for this job.

Dead Coin Battery

A dead battery is the primary cause of your Fiat 500 keyfob not locking or unlocking the doors. The coin cell battery in the key fob will deplete quickly when you don't utilize frequently enough. If your remote began to show signs of weakening such as a loss in range or stopped working completely it is likely that the battery is dead.

The battery in the key fob is held in place by steel clips for retaining. If the clips are loose, they could cause contact issues that will stop your remote from receiving power. Use a flathead screwdriver break open the retaining clip and then remove the old battery. Be sure to choose a replacement key for fiat 500 with the same type of voltage, size and specifications as the original battery.

The exposure to water can cause the key fob to corrode, or even become damaged. Even a short bath in warm, soapy water can damage the chip. It is best to keep your key fob in a dry area.

Water Damage

If your key fob isn't operating properly, it could be due to water damage. The rubber seals on key fobs stop them from being damaged by a tiny splash or drizzle of water. However, it's crucial to keep your keys out of the washing machine, the ocean and pool.

The key fob contains an electronic chip which sends an immobilizer of your car. This is what allows your 500 to start or lock, however if the chip gets wet, it's unable to longer function.

You can clean the internal electronics of your key fob using isopropyl alcohol, or an electronic cleaner to determine whether they're still in good condition. It is recommended to replace a key fob if it is submerged in salt water, rather than trying to fix it yourself.

Although a replacement fob may cost a little money, it's far less expensive than paying for your Fiat 500 to be towed to the dealer for repair! Additionally, you can make it yourself in just the simplest of steps. Just make sure you have the right battery type before you attempt to open your key fob. You can find step-by-step instructions for any car keyfob on the internet.

Faulty Chip

The chip located within the key fob communicates with the car's immobiliser system to ensure the vehicle is able to start when the correct key is used. If the chip is damaged, or corrupted in any way the car won't start.

Water damage or a dead battery are the two most common reasons for defective chips. Regardless of the reason, it is an ideal idea to hand this task to a locksmith since they will be able to repair the chip quickly and at a reasonable cost.

If your key fob does not function after being exposed to clean rain or tap water then remove the battery. Clean the electronic component using an old towel. If the key fob still fails to work it's likely to be a fried chip and will require replacement.

Some people will go to their dealer when they are in need of a new Fiat key fob, but this could be a costly alternative. If you're seeking a cost-effective method to get your Fiat key fob repaired, look no further than United Locksmith. We have all the tools and experience needed to repair your Fiat fob quickly and professionally. way.

Faulty Receiver Module

Fiat key fobs transmit a signal to the vehicle, which will unlock and close doors (and start the car for those with an automatic transmission) up to 50 feet. There are a few reasons why the fob might not function. This includes a dead coin battery or water damage or worn buttons or a problem with the receiver module, and signal interference or a malfunctioning electronic chip.

If the fob was located in the pocket of someone who has suffered severe trauma (such as being dropped on the hard floor or washed in the washer) the fob may not be in a position to communicate with the Body Control Module (BCM) of the car. The BCM is a security device that can only accept signals from genuine keys.

If this is the case, you will need to replace your fob. A professional locksmith is able to handle all aspects of the key replacement process and can even program a brand new one for the 500. They can even give you a clone fob that works the same as the original (and costs less than what it would cost).