peugeot boxer key 208 Key Replacement

Peugeot 208 key replacement is best left to experienced auto locksmiths who have the proper equipment and know-how. They will be able to create and program new keys much faster than a dealership would and at a lower cost.

A dead battery for your coin is most likely to be at fault the reason your key-fob stops locking or unlocking doors. However, there are other possibilities that the key is malfunctioning.

Dead Coin Battery

A dead battery can stop your Peugeot 208 from locking and unlocking, and also preventing it from starting the engine. In this situation you'll need to use the alternative starting method that is described in the owner's manual.

Another reason the 208 won't start is because the spark plugs are worn down. The spark plugs ignite the fuel to start the engine. They have a limited life span. They'll eventually degrade in the event that they aren't utilized enough.

There is a simple solution for this issue. The best option is to determine the voltage of your car battery using a multimeter. If it's below 11.5 volts, then you need to replace it. It is also necessary to clean the contacts of the battery in case it is corroded. This can be done by removing the rubber cover from the two battery terminals, and then using a wirebrush to clean any damaged parts of the battery. You should then reconnect the cables for the positive and negative poles.

Water Damage

If your 208 isn't starting and the battery is not flat then you should check whether the spark plugs are working. It could be that they are simply too filthy and don't spark. This can be fixed by cleaning the spark plugs in a workshop.

Peugeot cars have transponder keys that integrates with the car's immobiliser system. This ensures that only the correct key is able to turn the engine. If the chip inside the Peugeot key is damaged, it will not transmit the proper signal to the vehicle.

Water damage is the most common reason for this issue. This is most common in colder climates where the vehicle may have been exposed to rain or snow. If this is the case, call a reputable auto locksmith who has all the tools and equipment required to modify the new key. They will also have all the latest technology and equipment required to create the Peugeot smart key. The process shouldn't take more than 15 minutes.

Contacts to the battery are not working properly.

Peugeot changed from the old carbon-encased transponder chips and introduced a new kind of chip that utilizes electronic components within a circuit board. The new system is excellent in its initial state, but the circuit boards degrade over time and cease to function properly.

This could stop the immobiliser chip from triggering which means that your car won't start. Contact a Peugeot specialist, or a locksmith if this is the situation.

Another common issue is when the battery for the key fob starts to die, this causes the key blade to stop being able to feed into the lock. A car locksmith will replace the battery, and then cut a new key blade for you. This is a quick solution.

Faulty Receiver Module

If your Peugeot key fob stopped working after dropping it on the floor, getting exposed to a sudden downpour or accidently washing it, it could be due to a defective receiver module. The receiver is responsible for sending radio frequency signals to the onboard computer, which is responsible for controlling the centralized locking system within your Peugeot vehicle.

The rubber seals on the key fob prevent water from getting to the electronic chip. However prolonged exposure to water could penetrate these seals and damage the chip. The high salt content in the pool or ocean waters can cause damage to the key fob if it is submerged.

If your Peugeot spare key fob doesn't work You'll need the module replaced. This is only done by a skilled auto locksmith or Peugeot specialist. peugeot keys (check out this site), unlike other cars, are secured by an immobilizer device. This requires the right code to begin the car. It is for this reason that you should only trust the Peugeot locksmith to create and program the replacement.

Computers with faulty on-board computers

The on-board computer in your Peugeot is responsible for various features in your car, including power windows and airbags. When something goes wrong in these systems, it'll typically display a code that indicates the problem. This code is stored inside the system and will remain there until the problem is solved. Often, this will involve the on-board computer being replaced.

The most typical reason for the warning light for airbags to come on is corroded or loose connections within the sensor. This can occur due to wear and tear, aging, or exposure to salt and moisture. This issue should be addressed as soon as you can, since an airbag malfunctioning could be dangerous in case in the event of an accident.

If your Peugeot is showing a card detected as not present error, then the key battery in the key fob could be weak or dead. This will stop the key fob from sending a signal that will disable the vehicle's immobilizer. Test this by pressing the unlock button on the key fob and then trying to start your car. If this fails then the battery in the key is in need of replacement.