UPVC Window Repairs

uPVC windows are energy efficient and UPVC repairs help to reduce heating bills. As they age, however, problems can occur that need to be addressed. This can include faulty hinges, handles, or locks.

DIY people can fix wooden windows relatively easily. It's cheaper than buying a new window.

Cracks

Cracks and breaks can be a major problem. If windows are not properly repaired, they can result in water intrusion, less effective barriers to cold weather, and can cause structural damage. It is essential to locate an expert local repair or builder who specializes in repairing uPVC frames and can demonstrate the experience, skills and tools needed to produce the most effective results. This will ensure that the crack is fixed before it gets worse and you don't need to replace the window glass or window unit.

Small cracks in glass can be repaired by using a variety of home-based solutions. Superglue and masking tape are two of the most commonly used products to hold cracked glass in place for a brief time. For cracks that are more extensive, the tape may need to extend past the crack on both sides to get the optimal results.

Another option is two-part epoxy that can be used to repair broken or cracked glass. Hardware stores typically sell this product for about $10. Make sure that your workspace is prepared prior to mixing the epoxy. Also, make sure you have the right equipment for the job, such as a soldering iron.

If you notice that your lower or upper sash isn't lifting it is most likely due to the cords connected to the sashweights are damaged. It's an easy fix that can be accomplished using an extension ladder and a flat-head screwdriver. A rotted dripcap can also be repaired at home. Many home centers stock a drip caps that are not rot free and can be easily caulked or nailed in place. Also, if you have a double glazing- or triple-paned window, be sure to make sure that one of the panes is not broken. The reason is because the gases in the space between the windows are responsible for increasing the efficiency of the window and must not escape.

Water Leaks

If your uPVC window is leaking, it can cause damage to your interior and lead to costly repairs. Water leaks can also affect the structure of your house and lead to the growth of mold. It's important to address any problems caused by leaking windows right away to minimize the damage.

A damaged sealant around window frames is a common cause of leaks. Silicone caulking will restore the seal to its original condition and prevent leakage. Look for gaps and cracks around the window frame as well as the stone or brick wall that surrounds your windows.

Another reason for leaky windows is the drainage hole is blocked or faulty flashing. Make sure that the drainage holes haven't been blocked or UPVC repairs blocked, especially after heavy rain. It's also an excellent idea to check the flashing around the bottom of your window and ensure that it's sealed properly.

It's also crucial to make sure that your drip cap doesn't have any rot or is missing. A rotten or damaged drip cap can allow water to enter the window from above and cause damage to your home's structure. Replacing a drip cap isn't difficult and is usually a straightforward process of buying an entirely new one and nailing it into the right spot.

It's recommended to have your windows checked for water-tightness by a qualified. They can employ a specific tool to measure the water-tightness of your windows and make sure that they meet industry standards. If your windows fail the test, they'll require replacement. It's a costly fix however it's worthwhile to ensure the safety and comfort of your family.

Sagging

If your windows don't shut properly, it could cause a number of problems, such as drafts, condensation, and an increase in energy costs. It could also be an indication that the windows were not installed correctly or that the sealant is worn out. There are a few things you can try to solve the problem.

The first step is to prepare your workspace in a space that has plenty of light to repair your window correctly. Begin by laying newspaper or an old blanket on the floor to protect it from any splinters or drips that could be leaking from the window during your work.

Use a white cloth soaked in a solution of detergent and water. This will prevent any stains of color from appearing on your windows. When you are ready to begin working on your uPVC windows, start by making note of where the hinge channel must be placed. Then, remove the channel from the frame and fill in the screw holes with epoxy (for uPVC windows) or wood filler (if your frames are constructed from wood). Be sure to smooth the filled hole before it sets.

Install the hinge channel after the holes have been filled. Make sure it is centered on the window jamb and that you drill the holes for the new screws about a quarter inch from the original locations.

Next, measure the spindle that protrudes from the underside of your handle. You can order an alternative or bring it to a local hardware store for a replacement. Then, take out the setscrew on the shaft of the operator, and then smooth it out so that the set screw is able to secure itself to the shaft (photo). Then, your uPVC windows should shut easily.

Broken Hinges

It will be difficult to open or closing your uPVC windows in the event that the hinges are damaged or not working correctly. This could be a security problem and can also stop your home from being warm or cold. You can easily purchase a new hinge for your uPVC window. It's important that you use the right hinge for your windows.

This is because the hinges have to be of the same width to fit into the window frame. The most popular type of hinge used in uPVC windows is a standard 15mm or 18mm UPVC window hinge. There are also special hinges for wooden frames. The proper hinge will help you to avoid common problems with your windows.

Your window hinges may be loose or stiff for a variety of reasons. The hinges may not have been properly tightened. You can test this with a screwdriver. locate the friction screw at the end of the hinge and then loosen it. You can then adjust it by turning it in either direction.

If your UPVC window hinges are not functioning as they should, call Preston Glass Fix for a quick repair. Our technicians will evaluate the condition of your hinges for your windows and advise you on the best solution for your needs. We can repair or replace the window hinges, adjust them or install new locking mechanisms to ensure that your UPVC windows are safe and secure for years to come.

Locks that aren't working

UPVC window mechanisms and locks are an essential part of home security. They make it very difficult to open windows without breaking into the house. It can be a hassle when a lock malfunctions, but you don't need to replace the entire window.

It's often a minor issue that could have easily been avoided by regular maintenance. This is why we suggest getting your uPVC windows checked regularly by our annual maintenance program to help reduce the likelihood of problems.

The majority of modern uPVC windows come with espagnolette locks which operate by pushing the nose of the handle across a wedge block and then turning the handle to close the lock. They are extremely efficient in keeping the window closed, however over time they can start to fail if not properly maintained - we recommend applying WD-40 to the lock every couple of times a year.

If you find that your uPVC window isn't opening and closing as quickly as it did in the past, or if the lock doesn't function properly, there could be a problem with locking gearboxes inside the frame. This can be difficult to access as it requires the removal of the seals that surround the frame of the window and then taking off the handle.

A locksmith who specializes in UPVC repairs has the knowledge to identify the problem quickly and be able to repair the damaged gearbox for locking with an exact replacement. This simple and quick fix can save you hundreds of dollars by avoiding having to buy new windows.