Replacing uPVC Window Handles

Switching the handles for Double glazed doors of windows made of upvc is an easy job. It is essential to ensure that the new handle is fitted into the spindle cutouts in the window mechanism.

If the steps listed below are followed properly, any cockspur handle should fit in most windows. The step height of the handle is crucial.

What to Look For

As time passes, uPVC handles on many windows in the UK may begin to show signs of wear and tear. When this occurs, the window handle may become loose or difficult to operate, which makes it essential to replace it. This is a relatively easy task that can be completed by anyone who is familiar with basic hand tools.

The first step is to ensure that the handle is securely fixed to the frame of the window in the open position. The next step is to find the fixing pins or screws that hold the handle in place. These are usually located on the inside of the handle. They can be removed using a screwdriver and pliers.

When the handle is loose, gently pull it away from its hinges. Then, you'll need to locate a new handle that is the same style and size. This can be done on the internet or in an area DIY store, and the process should only take about five minutes with the help of a screwdriver.

When replacing the handle on a uPVC handle It is crucial to think about the step height. This is the distance from the bottom of the handle to the point at which it sits on the window frame. It is generally an average measurement, but it is important to determine the step height of your existing handle before purchasing an entirely new one.

There are several sizes depending on the kind of handle. Inline handles for double glazed doors for uPVC windows generally have 31mm lug centres, and there are also varieties of cockspur handles with 43mm centres. Tilt and turn handles are often used on windows made of uPVC, and they come with a unique design that allows windows to be slid up for ventilation, and then rotated to open the window fully.

The most common uPVC handle breakage is internal cracking, rather than a fracture from the base. This can make it difficult to open. It is important to ensure that any replacement handle is fitted with the same spindle as your original one.

Remove the Old Handle

A poorly installed or damaged window handles may cause double-glazed windows to open and close incorrectly, and can cause them to become stuck. There are many reasons like general wear and tear, or corrosion of the handle made of metal. In these instances, it is important to seek replacement window handles made of upvc as soon as possible in order to prevent further damage and loss of functionality.

One of the first steps to do when replacing window handles made of upvc is to remove the old handle from the locking window handles. Start by removing the screw with the handle when it is in a closed position. Once you have removed the screw, you can take off the handle. It is recommended to use an electric screwdriver for this since it will make the task easier and quicker.

It is also important to be aware that screws can be hidden in plastic caps. It is best to remove the covers with a Stanley knife. Once the old handle is removed, you must look at the square cut on the base of the handle to ensure that the new window lock handles will work with it. It is essential to measure the spindle length on the handle that was used and then compare it with the size of the window mechanism spindle cutout.

The different types of upvc window handles are: Espag handles, which feature a central screw that can turn left or right; Cranked handles, which have two screws and are typically found on tilt and turn upvc windows and Spade handles which have a flat arm and can be placed on either side of the window. It is simple to replace the handle when you've found one that is suitable. Simply screw it into the frame, and make sure the spindle is correctly inserted into the lock mechanism. Once this is done, it should be tightened to the window frame and the replacement window handles made of upvc should be secure.

Take a measurement of the Spindle

If you're replacing a Upvc window handle that has come off, it is likely because the spindle holding it in place has become damaged or loose. In certain situations it is possible to tighten the spindle using pin or screw. In some cases it might be necessary to replace the handle. There are many types of upvc window handles. There are three kinds of handles for internal bifold doors: inline espagnolette, cockspur, and tilt-and-turn. Each type of handle is installed and replaced in a different manner.

It is crucial to measure the current handle before purchasing a replacement. This will ensure that the new handle is the correct size and will fit correctly within the window. All handles are calibrated according to industry standards, making it easy to determine the right size.

To determine the size of your handle first remove it from the window by turning it back to the open position. You should be able to see the size of the screw or pin that secures the handle. Then you can use the ruler or tape measure to determine the length of the spindle. Once you know the length of your spindle, it is possible to buy a replacement of exactly the same length.

The step height of a upvc window handle is also important to take into consideration when you are buying replacements. The step height is the distance from the base of the handle to where it rests on the frame. In general, this is approximately 21mm for uPVC windows and 9mm for aluminium. To be sure that the new handle is suitable it, handles for double glazed Doors you can drop something into the space to determine the distance it will go before meeting an obstruction.

Cockspur handles usually have different backset heights depending on the type of window handles for wooden windows they are placed in. Inline Espag handles have the standard height of 43mm centre to centre (2 fixing points). Cockspur handles, however, have different backset heights dependent on the design of the window they are in. This is due to the fact that they have a spur which extends from their handle and is locked onto a cockspur wedge hitting plate.

Fit the New Handle

If you've decided to replace the handle, carefully align it with the screw holes in the door and fix it using the screws supplied. If you're also replacing the latch lever, it can be installed in a similar way to the main patio door handle with lock handle. After that, attach the door trim to conceal the screws for mounting.

Tips: To remove the metal head from a wedge made of wood, place the handle on the floor, so that its wide end is on the ground. Then use an hammer and tap the thin end. Be careful not to damage the handle or handle spindle.