Repairs to uPVC Windows

uPVC is a fantastic choice for modern homes. They are long-lasting, durable and easy to maintain. Unlike timber and aluminium, they are not susceptible to corrosion or rot.

It is important to clean and oil UPVC windows and doors on a regular basis. This will prevent unnecessary repair costs and increase energy efficiency.

1. Broken Glass

The broken glass in your windows can cause severe damage to your home, and could even be fatal. You should take the time to make sure that your windows are in good working order.

For single pane windows, it can be relatively simple to replace windows, and the new one will usually fit inside the frame that was previously installed easily. However when you have double glazed window repairs near me pane windows that are held in place by internal beading, it'll be more difficult to remove the existing panes and install new ones. In this case, it is necessary to purchase plastic spacers in order to help the new pane fit into the window frame.

Wearing protective eyewear and thick gloves is a must for anyone who plans to remove the glass yourself. You should also lay down a dropcloth before you begin working on the window panes so that any shards fall onto the fabric, not onto the floor and could be trampled under.

Once the glass is removed, it's a good idea to seal the gap with clear packaging tape or duct tape to block drafts and Repairs to uPVC Windows water from entering the property until a professional comes out and repair the window. This also serves as a barrier to prevent any criminals from getting into your home. If the gap between the window repairman near me and the door is substantial, you may need to consider security screens that includes windows. This will provide the best of both.

2. Sagging

Upvc windows and doors are an affordable energy-efficient, durable and long-lasting alternative to timber windows made of sash. However, over time they may be afflicted by a variety of issues like sagging. A sagging window in uPVC can cause problems with light, draughts and even security. It is crucial to act when you discover that your uPVC windows are sagging.

Repositioning the hinges can help fix a window that is sagging. First, you'll need to open the windows to access the frame. Then, remove both the hinges at the top and bottom using a screwdriver, and then adjust them clockwise or counter-clockwise. Once you've repositioned the hinges, shut your window and verify the fit. If you are happy with the fit of your window, tighten the screws to hold them in the right position.

If you aren't able to move the hinges, you might require replacing the seal. Rubber seals can dry out and lose their elasticity over time, causing them to lose their tightness. It is essential to replace your seal as soon as you can to keep your uPVC window watertight and draughtproof.

uPVC handles could also become loose. Most often it is due to screws that have come loose over time. However, it could occur because the handle mechanism has been worn out. It's fairly simple to fix a loose uPVC handle. First, you'll need to close the window and perform an initial test fit. The corners of the sash should align with the casing joint. If it does not, you can use the screwdriver to loosen up the handle. Then, turn the mechanism to position.

3. Water Leaks

It is important to act if you get up each morning to find a smoky wall and floors that are wet. The leaks of water through windows could cause structural damage to your home and also impact your ability to regulate the temperature of your home. Most of the time, uPVC window leaks are caused by damaged or missing sealant.

This is an easy fix that can be accomplished by anyone who is a DIYer with the skills. Depending on how serious the issue is, old caulking might need to be removed. It is crucial to keep in mind that when it comes to uPVC window repairs, you should not be tempted to apply too much caulk' as this will only make the area harder to clean and reduce your energy efficiency.

Make sure that the drainage holes do not have debris inside them and that the sill pan is properly angled to allow the water to drain from the window. In more serious cases you may need to think about replacing the window.

Mold spots and rotted sills are also signs of water leakage. The is a fungus that thrives in damp conditions and is able to quickly spread throughout the home.

It is also important to note that if the leak is coming from between the glass of your double-glazed windows, it's more likely to be an issue with the glass seal rather than the frame or sagging. A uPVC specialist can easily solve this issue by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or loose and open with a breeze It could be hinges at the fault. Any competent DIYer can replace hinges in just a few minutes.

Most households in the UK will have either top hung or side-hung uPVC windows that are hinged and, just like any mechanical component they will wear out over time. It is very easy to change a window hinge, but it's easier if someone helps you hold the frame.

Make sure that the uPVC hinges are open and closed in the proper direction. You can do this by looking for the arrows on each hinge, this indicates which way the window should open.

The problem can be caused either due to opening the window in the wrong way or a faulty installation at the factory. Sending us a photo via our website will often resolve the problem. We are always happy to offer advice.

Regular lubrication of the hinges is also necessary. This can be accomplished by applying an oil that is light in nature to the hinges. We suggest using a solvent-free lubricant such as 3-in-one Multi-Purpose Oil. Regular lubrication can make the window easier to open and close. It can also lower the risk of a window sticking and prevent corrosion. It is recommended to perform this every year. WD40 or other solvent-based oils should not be used as they can cause damage to your uPVC windows.

5. Draughts

Draughts in upvc windows can be caused by a variety of different factors. Firstly the hinges, again due to wear and tear could become misaligned. This can cause gaps to develop where the sash meets the frame. These can be easily repaired by giving them a good cleaning, but if they are beyond repair it might be necessary to get them realigned or replaced. In addition, the interlock could also become unbalanced. It is located on the hinge's side, and Repairs to uPVC Windows could require to be cleaned. In some cases it might be necessary to replace the hinges.

The second most frequent reason for draughts is window seals, these can become worn down or damaged over time, and will allow air to escape through these gaps. This can be avoided by replacing them with high-quality weatherstripping. Another alternative is to replace the upvc window with low-emissivity glass, this will help in regulating indoor temperatures and again will lessen the possibility of draughts.

One of the most effective ways to reduce the draughts in your home is to use a draught excluder, these are typically made of fabric filled with some kind of filler. They can be placed on the top of your windowsill. These will keep your home warm by blocking out cold air.

With a little maintenance and repairs, your upvc windows will continue to provide a great level of security and insulation for your home. However, it is important to realize that all windows have a life span and there may come the point when it's more cost-effective to replace them rather than repair them. If you are experiencing issues with your Upvc window you should consult an expert as soon as possible.