Reasons Why Your Nissan Qashqai Key Fob Won't Work

The Qashqai's larger dimensions give it an SUV feel. Its 19-inch alloy wheels on Ti and STL models may also be firm. The front tyres of the Qashqai can lose grip on rough surfaces, and its CVT might occasionally exhibit wrist-flexing torque steer.

It is usually due to the battery being dead, which can be replaced in a matter of minutes. Make sure that the replacement battery has the same voltage, size and specifications.

Water Damage

One of the main reasons that a nissan key programming key fob will give the "key ID incorrect" message is due to water damage. The rubber seals on the key fob shield the chip's electronics, but long-term exposure to moisture can cause it to malfunction properly. This is typically the situation when you drop your key fob into the ocean or a swimming in a pool, but it can also happen if it gets wet from soapy hands or rain.

If your key fob is exposed to water for a long period of time, it could need to be cleaned with isopropyl alcohol, or electronic cleaner. It may also require the attention of a professional to repair or replace it.

If your key fob need to be replaced the process is easy. Make sure you have the right multipack (CR2032 3V). Then open the back and front cases with an abrasive screwdriver. You'll need to remove the clips that hold the metal together and remove the old battery and put in the new one. After reassembling the fob, put the mechanical key back in place and verify that it operates correctly. If not then you'll have to bring it to a local Nissan dealer or an experienced locksmith to replace the key chip. The chip isn't usually damaged by water and therefore isn't too costly.

Dead Coin Battery

Another reason that the reason your Nissan Qashqai key fob might not work is because the battery for the coin is dead. These batteries last 3-5 years, but they are prone to failure over time if the fob has been dropped often. You can replace the battery but ensure it's the same voltage and the same size as the original. If you choose to use a brand new battery, it could cause the key to be assigned a wrong key ID. This will stop it from being linked to your vehicle.

The most efficient method of replacing the battery in a Nissan Qashqai key fob is by opening the fob with a small flat head screwdriver. In the screwdriver, push it into an angled notch on the bottom of the fob and twist it gently to split the two parts of the key fob. Remove the old CR2025 battery and replace it with a new one, observing the position of the previous one inside the fob.

Check the terminals for any water damage or dirt before installing the new battery. If so clean the terminals using some isopropyl ethanol. Make sure that the pole cables are connected correctly. They should be connected to both the positive and negative poles of your battery.

Troubleshooting

If your Nissan Qashqai's key fob doesn't function after exposure to water that is clean from a tap or rain it could indicate that there is a problem with the internal chip. You'll require a new keyfob if you can't solve the issue by replacing the battery. If the key fob stopped working after you dropped it, it's likely that the chip inside was damaged. If you clean the chip using isopropylethanol and paper towels and then put it back in the key fob, you'll usually get it working again.

Key ID Incorrect is a typical error that can be seen on the dashboard of your car. This means that the car is unable to recognize the key fob and not allow it to start the engine. This can happen in various ways, including water damage, problems undetectable within the key fob circuitry or RFID interference.

If the 12 volt battery in your key fob dead or not providing enough electric power, it will stop working. This can affect your Nissan Qashqai's keyless system central locking, as well as the capability to start the engine with the key fob. Check the batteries inside the key fob if it is not able to lock or unlock your door manually. Try installing the battery again to reset your transmitter.

Reprogramming

If the key fob had not been submerged in salt water and is unable to return to life after a simple wash with clean water. You can also try cleaning the electronic chip using isopropyl ethanol or an electronic cleaner. If these don't work, it may be time to replace the entire key fob by a new one.

If your Nissan Intelligent Key is still not functioning, there may be a problem with the connection between it and your car. To relink it, start by turning the key in the ignition, without turning on the car. Repeat this process until the hazard lights flash twice. Then, turn off your vehicle and remove the key.

Open the fob compartment of your vehicle's fob compartment. It is usually located on a door's jamb or the handle for the driver's door. Find the button that says "program" and press it. You should hear a chime sound after the process has been completed.

It's time to put your Intelligent Key to the test. Stand some distance away from the vehicle, and hit all the buttons on the key. If the lights flash and the horn sounds this means that the key has successfully linked to the Nissan. You can also test it near the Nissan.