UPVC Window Handle Replacement

Replacing a damaged or broken window handle is a relatively easy process, and with the right tools it can be done quite quickly. It's important to identify the kind of handle you have and its spindle size before purchasing an alternative.

Older uPVC window handles have a spur that protrudes and locks over the wedge striker for cockspur. They can be left or right-handed and must be to match when replacing.

What kind of lock or handle do you have? I have?

There are a myriad of windows locks and handles made of upvc each with their own advantages and purposes. The type of handle that you choose will determine if your locking mechanism is efficient and if it's easy to open the windows. Over time and through regular use, upvc window replacement panes handles may become damaged or worn out, rendering them less secure and efficient. In some instances, they may even disappear completely. If you find that your window handles have been removed, it's crucial to fix them as soon as you can. This will stop possible burglaries, and keep your house safe.

The good news is that replacing your window handles made of upvc is a relatively simple task that can be done by everyone. You will need a few tools, but with right knowledge, it is a straightforward process that should take only a couple of minutes. You will need to be aware of the type of lock or handle you have on your window. This will help you choose the appropriate replacement.

Inline Espagnolette Handles

These are the most common kind of upvc handle and are usually placed on the side of your window. They are flat in design and have a latch that connects to the locking mechanism on the window frame when it is turned. Inline upvc handles come with an elongated spindle that runs through middle of the handle into the window frame in order to operate the latch.

Cockspur Handles

These handles are usually found on older uPVC window frames. They have a distinctive, hook-shaped design. Cockspur handles have one screw that is used to secure the handle to the window frame and are not as secure as other types of window handles.

Handles that turn and tilt

As opposed to the other handles made of upvc, tilt and turn handles can both be rotated to open the window and tilted inwards to allow ventilation. They have a 7mm spindle on the back and are available in left and right-handed versions.

When purchasing replacement handles made of upvc It is crucial to measure the spindle's length since not all of them are the same size. Drop something in the middle of the hole to test the length. This is the maximum size of spindle that will fit in your windows.

What is the spindle?

uPVC window handles function in a similar way to doors, by turning the handle to open an opening inside the frame. The window then opens and closed. However, sometimes the handles may become damaged, particularly if they are regularly used or exposed to extreme weather conditions. You may have to replace the handles on your uPVC window if they're not able to operate it properly.

There are a variety of uPVC handles available comprising Espag, Cockspur and Spaded handles. They are designed in a variety ways to fit into uPVC frames. Each handle type utilizes a different spindle to lock the window mechanism. This is why it is essential to identify the type of handle is installed on your uPVC window to get the correct replacement.

You can find out what kind of uPVC handle you have by taking a look at the base of your handle. A snap-in cover is over the screw that holds the handle's base in position. When you remove this cover, you will be able see the second screw that holds the handle base in position. Once both screws are removed you should be able to pull the handle away from the uPVC window.

After you have removed the uPVC window handle, you have to carefully unscrew the spindle that was previously attached to the locking mechanism. Be sure to note the length of the spindle since you'll need to make sure that you buy one that is the same length as the original handle and locking mechanism.

The primary issue with window handle problems with uPVC is that the spindle becomes worn out and cannot longer work with the locking mechanism. This can be caused by corrosion, damage caused by frequent use, or an unreliable locking mechanism. When this happens it will be necessary to replace the window handle and the locking mechanism to restore complete functionality to your uPVC windows.

How do I get rid of my old handle?

Window handles can become damaged or destroyed over time. It is important to fix them as soon a possible to ensure your security. It is easy to replace a worn or damaged handle. The task can be accomplished in less than a minute without the need for any special tools.

The first step in removing the handle that was previously used is to remove the screw situated at the top of the handle base. After the screw is removed, the handle can be pulled away. A second screw is located at the bottom of the handle. It can also be removed. Once these two screws have been removed, the handle will be detached from the base of the window.

After removing the old handle and fixing holes, align the holes of the new handle to the existing holes in the window frame. There may be a little sticker or caps on the new handle, so take them off them if needed and then screw the handle into its place. Once the handle is set, it is crucial to verify whether it functions by turning the handle and making sure that the lock mechanism activates.

Espag handles come with an extra spindle that is protruding from the handle and slots into a multipoint locking mechanism in the window frame. Cadenza windows come with an edge with cut-outs which slot into the lock mechanism while Cockspur handles have an extended nose that hangs over either the frame's outer or transom bar cross member inside the window.

After you have put in the new handle, slide the spindle inside the window lock and tighten it. When the handle is fixed in place, replace the'snap in' cover and Upvc Window Handle Replacement screw cap (if appropriate). When the handle is ready for use, simply open and close the window a few times to ensure it works correctly and securely.

How do I install the new handle?

Changing your uPVC window handle isn't a big deal and the process is actually very simple. All you need is a screwdriver and small amount of patience. First, ensure that the handle is not locked. Then remove any screws visible. You can also replace them using screw caps. After removing the handle, you will need to note the length of the spindle that extends from the back. This is crucial since it will determine the type of handle that you will require to purchase.

Espagnolette handles are the most popular type of handle for uPVC windows. The spindle passes through the handle to activate the locking mechanism inside the window frame. When the handle is turned it opens the latch on the window and allows it to open. In regular use and over time, UPVC Window Handle Replacement espagnolette handles may be damaged.

Cadenza handles are a different kind of uPVC window handle that is commonly used on tilt and turn windows. They feature a protruding knife that is operated by a multi-point locking mechanism within the window. They are generally more secure than handles made of espagnolette because they can only be opened from the inside. They can be replaced by the same method as espagnolette handles but you will need to ensure that the new handle has an angled blade as opposed to one that is flat.

Once you have determined the right handle to purchase, you can simply line up the new handle with the screw holes, and then screw it in place. After that, you can put the screw covers on and test the new handle. This is accomplished by moving the handle from the locked to the unlocked position and vice versa several times. If you have any issues, it might be beneficial to speak with a professional to determine if they can assist you in solving the issue. They are often able to advise you on the best approach to resolve the issue in a fast and efficient manner.