How to Fix a Dead Kia Picanto Key Fob

The kia key fob replacement Picanto was built for the city. It can zip through gaps in traffic that bigger cars can't and can wiggle through width restrictions like they aren't even there. Despite its ugly appearance it is packed with plenty of kit.

There are many reasons that the key fob on your kia Picanto may not work. The most frequent reason is an inactive battery.

Dead Coin Battery

The most common reason that a Kia Picanto key fob stops working is a dead battery. The key fob is likely to show warning signs like erratic behavior or losing range before dying. If you observe these signs, it is best to replace the battery before it completely fails. Make sure you choose an alternative battery that has the same size, voltage, and specification as your original one.

If the key fob not working, you might require it to a dealer. This is the only way of ensuring the replacement will be programmed correctly and compatible with your vehicle. The process of reprogramming a key fob without the proper procedure can damage the chip's internal circuit and cause it to stop functioning.

Another possibility is that the receiver module has developed a fault. This could be because of a chip that has been damaged or wear and tear. The symptoms of this problem may be difficult to detect however it is crucial to determine the cause immediately. If you're not able to get your key fob to lock or unlock the doors, or even the spare key isn't working then it's time to call a dealership or service center to get help. They'll be able to identify the problem and fix it.

Faulty Chip

The key fob comes with an embedded chip that sends an electronic signal to the car's computer. If the chip is damaged it will not send the correct code, and the immobilizer system of the car will be activated. This can be caused by several reasons. One reason could be an insufficient battery in the key fob. Another is water damage. If the fob becomes wet, it is very likely that it will cease to function.

A damaged chip may be the reason behind an Picanto key fob that isn't turning on the engine. If you've replaced the battery, and then tried to program the fob but it still does not work, it may be because the circuit board is damaged. If this is the case, you'll require replacing it.

To open the Fob, you must press the button on the back of the fob. Once you have done this, you are able to take off the mechanical key. You can then follow the video below to replace the key fob's battery. Make sure you choose the correct battery with similar in size and voltage. If you use the wrong battery could cause damage to the Fob. After replacing the battery, you should test it by pressing the lock button. If it works, then you have a reliable Fob.

Faulty Receiver Module

Your key fob endures quite a beating and isn't a perfect piece of equipment. Over time the batteries' contacts and buttons of your key fob can be damaged. Fortunately, it's quite simple to repair this yourself with a few simple tools.

To function, the fob needs to send a signal through a receiver in your car. If the module is not functioning properly the fob won't be able to open or start the car. There are many possible causes of this problem, but the first thing to try is resetting the fob.

This is typically done by disconnecting the battery with 12 volts in the fob and allowing it to drain completely. Connect the positive and negative cables by reversing their order.

If the battery is in good health and the fob does not have any water damage, the issue could be related to the signal. This can be caused by several things like interference from nearby transmitters, or objects that use the same frequency band as the Picanto's receiver.

Key fobs are designed with rubber seals in order to protect the chip inside from getting wet, but if they are submerged in water for long periods of time, the chips can be destroyed. It's important that you keep your key fob out of the water and only use key fobs with waterproof designs.

Incorrect programming

A Kia Picanto key fob is an efficient way to unlock and start your vehicle. You can also use the key fob to control your vehicle. It is important to learn how to use the key fob correctly especially in adverse weather conditions or if you are unable to move. There are many Kia Picanto keys tricks that can assist you.

If your key fob suddenly stopped working, it could be a problem with the internal chip. It's rare however it is possible. It is best to visit an Kia dealer to pinpoint the issue.

You can also try to reset your Picanto key fob. The procedure is fairly simple and can be completed at home. The first step is to take off the key fob. Connect the diagnostic tool beneath the dashboard to the OBDII connector and then start the engine. The diagnostic tool will then request information about your Picanto. This includes the VIN number, make and model.

You can also look for dead batteries. The metal clips inside the key fob secure the battery and complete the circuit. If the retaining clip is not secure it could interrupt the flow of electric current, resulting in an interruption in the function.